What did you do with your 60 this weekend? (30 Viewers)

[Spook50]

Fixed my cruise control knob that was just hanging loosely, replaced my heater C/B so my A/C would work again without kicking off, pulled off my grab handles to clean all the black buildup off of them (overnight soak in Simple Green does the trick) and lubed my speedometer cable. Speedo needle is much more stable now.

 

[Godwin]

Swapped out the old 5 speed knob for a new one. Never really liked the rubber knob.

 

[Tennessee80]

Swapped out the old 5 speed knob for a new one. Never really liked the rubber knob.

View attachment 2035913View attachment 2035915

That’s a good problem to have! My knob only goes to 4...

 

[TRAIL TAILOR]

Finally these are at a place that I can make them available to you all.

Reproduction Fender Vents - 60 Series

CNC Milled from 6061 aluminum Available in two finishes - bare aluminum or black anodized Ships with new custom EPDM 70 gaskets and 316 stainless steel trim screws Sold in pairs Please allow one week for shipping on bare, two weeks for anodized

trail-tailor.com

J

 

[TRAIL TAILOR]

View attachment 2034326

View attachment 2034333

View attachment 2034338

F,

I got mine rolled about the same position. I'm running the canister/cat set up so a had a little more clearance issues, but got it done.

J

 

[Dustin Messina]

Pulled it apart...

 

[TRAIL TAILOR]

Keyed the crank, removed the doors, stripped the crap padding, steering stabilizer, front shocks and laid out the dual exhaust.

J

 

[1811Retired]

My 60s been with Nick @ Adventure Fab in Vancouver, Washington getting the rear tire carrier built. He works out of his own home. Custom bumpers and racks is all he does. Very talented guy who builds anything how you want it. He likes to incorporate your vision with his knowledge and experience to build a quality product at a great price. My bumper is almost done. Added rear quarter panel sliders off the rear bumper. Today he’s building sliders.
View attachment 2034597
View attachment 2034593
View attachment 2034596
View attachment 2034594View attachment 2034595

Does he have a website?... nice set up!

 

[MANUCHAO]

got it done

I saw the pics on the other thread as well... looks great...
What engine you running ?
I know it's a 6.2, but I'd it a Gen lV, or V?
Are these slightly narrower than the Gen III?
The exhaust mani clear those narrow rails really good..!!

 

[TRAIL TAILOR]

I saw the pics on the other thread as well... looks great...
What engine you running ?
I know it's a 6.2, but I'd it a Gen lV, or V?
Are these slightly narrower than the Gen III?
The exhaust mani clear those narrow rails really good..!!

Gen IV Erod, stock manifolds. I raised the motor 1" from where most would place it IMO, it gave me a little more room at the frame/manifold point. Other wise the flanges would be really close and I knew I needed to roll and play with the downlegs to the CATs.

J

 

[MANUCHAO]

I raised the motor 1" from where most would place it IMO, it gave me a little more room at the frame/manifold point.

This......!!!

Im glad i swapped to these LS3 manifolds.... but headers would of been awesome....ah well....

 

[Shes Mad]

Took about an 800 total mile road trip in the 60 to the Indy car races in Iowa. Super hot, and of course had AC problems. I noticed it seemed to be getting a little warmer, so I put a thermometer in the vent. It was about 65 degrees. In about an hour, it was still 65, then 70, then 80 2 hours after the initial 65 reading. Then it was give up time. I checked refrigerant when I got to my destination and it was right where it should be, compressor clutch was engaged. I believe the compressor failed to compress. It was running, but not cooling. So it got pulled last night. Not fun, as it was real tight. Note to self—should have replaced it when I put the LS motor in.

Hope that fixes it

 

[DirtRoads]

They are close to production ready if there is enough interest.

If there were an unwelded DIY kit available, I would be so down.

 

[tmxmotorsports]

Keyed the crank, removed the doors, stripped the crap padding, steering stabilizer, front shocks and laid out the dual exhaust.

J

View attachment 2036042
View attachment 2036049
View attachment 2036045View attachment 2036046View attachment 2036048

J put an h pipe in on your exhaust it will smooth out the sound and won't be as choppy from left to right

 

[cheeese]

I got the USB dash blank installed, since the cig lighter has never worked for lighter adapters I wired it directly to the acc power and ground leads for the lighter.

But I found two mystery plugs loose behind that lower bezel, one two wire W/G and R/G, one four wire W/B, Bl, Bl/W, R/G:

They don't appear to connect to anything I could see inside the dash, any ideas? The wiper, defrost, and rear heat all are connected and working.

 

[Rabango]

Installed the window felts things. Such a minor addition but makes such a huge difference. Thanks so much @Comet

 

[RredFJ40]

That’s a good problem to have! My knob only goes to 4...

But at least reverse is in the right spot!

 

[jmkfj60]

Replaced center and rear dome lights with new OEM parts. Got driver side snake binders put back on with new clips. The LED lighting in the cab with the dome lights is awesome.

 

[RodrigzCrzr]

Installed a new Wheelskin leather cover on “Dusty”

 

[BlackCat]

The never ending saga. Put an A/C compressor on it, the condenser o-rings leak. Put condenser o-rings in it 3 weeks after I did the compressor and now the radiator is leaking. I feel like these things liked to be worked on. Like the truck is all “Hey, he hasn’t popped the hood in a couple of weeks, better start leaking something!!”