Rear lower control arm bracket protection

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

The 125 RLCA skid sets arrived today and they are WRONG. Somehow the laser shop made them to the Rev1 design instead of the Rev 2 approval.... They are re-cutting and bending as I type this and will re-ship to me tomorrow. I should have the CORRECT ones on Wednesday.

Sorry for the delay, but nothing I can do about this... An 1/8" and attention detail is a red line in the accounting books no matter how you look at it.

Here is what a $7440.00 FU$K UP looks like.....

IMG_20170410_151437278.jpg
 
:eek:
 
reevesci said:
The 125 RLCA skid sets arrived today and they are WRONG. Somehow the laser shop made them to the Rev1 design instead of the Rev 2 approval.... They are re-cutting and bending as I type this and will re-ship to me tomorrow. I should have the CORRECT ones on Wednesday.

Sorry for the delay, but nothing I can do about this... An 1/8" and attention detail is a red line in the accounting books no matter how you look at it.

Here is what a $7440.00 FU$K UP looks like.....

View attachment 1438311
Click to expand...

Ouch-

Export......
 
reevesci said:
The 125 RLCA skid sets arrived today and they are WRONG. Somehow the laser shop made them to the Rev1 design instead of the Rev 2 approval.... They are re-cutting and bending as I type this and will re-ship to me tomorrow. I should have the CORRECT ones on Wednesday.

Sorry for the delay, but nothing I can do about this... An 1/8" and attention detail is a red line in the accounting books no matter how you look at it.

Here is what a $7440.00 FU$K UP looks like.....

View attachment 1438311
Click to expand...


Its not the fawkup, its the speedy recovery that counts;)
 
I'm not worried about getting it fast, just want it done correctly. Thank you for your attention to detail!
 
Wow that sucks J. Benc ran in to something similar when doing his rear bumper. I guess it's what you say. Needle in haystack to find a good cutter. We appreciate your attention to detail no rush!
 
These are impressively stout - hope to have them finished and installed this weekend. Thanks, @reevesci!

041217_rear_LCA_armor.jpg
 
Jason I just got home from a trip to find them in my mailbox , these are the correct ones I assume ? Thanks they look very beefy
 
Got mine this eve. Hope to have them welded on this weekend.
 
How come they are not symmetrical? It appears the skid plate part on both angle off to the left. Wouldn't it make sense for one to angle off to the left and another to the right?

Granted, I have not crawled under my rig to take a look yet..
 
Sho
SanDiegoCruiser said:
How come they are not symmetrical? It appears the skid plate part on both angle off to the left. Wouldn't it make sense for one to angle off to the left and another to the right?

Granted, I have not crawled under my rig to take a look yet..
Click to expand...

Should be a left and a right angled one.

J
 
You must log in or register to reply here.

Similar threads

Todrn55
Part inquiry..lower control arm
Replies
2
Views
367
Todrn55
Todrn55
L
rear upper and lower control arm replacement
Replies
7
Views
795
porschenut
porschenut
akrafty1
Lower control arm nut and bolt part numbers
Replies
7
Views
1K
2001LC
2001LC
A
AHC troubles after SPC control arm install
Replies
1
Views
348
ODSTbee
O

Users who are viewing this thread

Total: 1 (members: 0, guests: 1)

Share this page

Back
Top Bottom