Pictures of your Maxtrax mounting solution? (1 Viewer)
- Thread starter CharlieS
- Start date
This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.
Clickitty click click.
Tappity tap tap.
LOL!!!
BRG high dollar poly vinyl stuffs.
Yeah, the bag is nothing special to be honest, but it keeps the dirt mostly contained.
I have mine in a soft bag I bought used. It fits up to four and slides behind the second row seats between them and my Trekboxx system. Flip the seat back up and they are out of sight, out of mind, until needed.
Markuson
SILVER Star
That’s an A/C outlet powered by my large interior inverter. On the other swing out, I have a male, A/C power in...since my fridge runs 24/7. Let’s me plug in at home easily iin about 3 seconds sothat my dual batteries are regularly tended and my fridge power is taken over by house current.
MyBrain is broken or I’d tell you my antenna brand. Very happy with its kocation.
Markuson
SILVER Star
I often do the same when i carry alll 4 boards.
Not sure if anyone has seen these, but I ran across it on instagram a couple of weeks ago. It looks like a nice secure mounting bracket for a roof rack. Unfortunately they are a little expensive for me.
Recovery Board Quick Mount (RBQM) for Maxtrax - Expedition Essentials
Recovery Board Quick Mount (RBQM) for Maxtrax - Expedition Essentials
TheGrrrrr
GOLD Star
I went with the rhino rack side mount.
How do you like those safari rails on the Rhino Rack?
TheGrrrrr
GOLD Star
They have been great and added little to no wind noise. The light bar works well as a fairing.
CharlieS
GOLD Star
- Thread starter
- #34
I opted to try the @mcgaskins approach. It worked well. The only thing I wish I'd done differently is to not follow the 27cm (side to side) base hole spacing - since there is a little bit of curvature to the crossbar ribs, the tops of the posts are more than 27cm center to center. The boards still fit, but it takes a little bit of encouragement to align them. I think if they were 3-5 mm closer they'd for better. I might adjust them when warm weather arrives. A teeny bit of elongation of the mounting holes would probably suffice.
leucadiacruiser
SILVER Star
The tracks you may not want inside your vehicle. Usually is some slick mud where you need them and unless you have water and a spray hose they are going back on your vehicle coated in mud.
I have been zip tying them up to my roof rack when I go places I'll likely need them, but ideally I like the rear bumper spare tire attachment some of the other guys have setup.
I usually only carry 2.
I have been zip tying them up to my roof rack when I go places I'll likely need them, but ideally I like the rear bumper spare tire attachment some of the other guys have setup.
I usually only carry 2.
From the makers of the fake Maxtrax:
X-BULL Recovery Tracks Mounting Hardware Pins Fixed Frame 4PCS Easy To Install | eBay
Nuts & flat washers are included. Size: 13.8X10.8X6CM.
www.ebay.com
What I'd love to see is a slim container sized for two MaxTrax, that would live either under cross bars on the roof, or part of a drawer system in the rear. All it would need to do is enclose the MaxTrax to keep the dirt contained, and have (lockable?) opening on the end into which you'd slide the MaxTrax. Basically a box with an open end.
I know @benc from Dissent fame had a similar container on some of his builds.
I know @benc from Dissent fame had a similar container on some of his builds.
- Joined
- Sep 22, 2018
- Threads
- 86
- Messages
- 1,085
- Location
- Noblesville, IN
- Website
- www.edmartintoyota.com
Front runner for me, only problem is I can’t get in my garage with the bracket on, so I have to attach before I go on a trip.
