FJ62 Cold start injector time switch advice (2 Viewers)

[lord2lord]

I can help here :

YES drain your Radatior say only a gallon or so , is needed to remove :

then :

you have all this to consider what all you needs and wants are in the world of the 3FE thermosts housing :

FJ62 3FE PLUG and PLAY Repair KIT OEM Genuine NipponDensso JAPAN , Fuel Pressure Temperature Sensor , SENDER WATER TEMPERATURE Gauge Fits 87 -90 . GREY TIP 1 wire comes with the OEM Connector Plug , Seal and Extra YAZAKI OEM Terminals - VintageTEqP

NOTE: This DOES NOT Come with the Wires Attached to the connector .... Genuine NipponDenso OEM JAPAN Parts Comes with...

vintageteqparts.com

3FE PLUG and PLAY REPAIR KIT OEM Toyota BVSV VSV Valve, Bimetal Vacuum Switching, NO.2 ( FOR E.F.I ) 25820- Fits 88 -90 FJ62 USA & Canada Spec. sensor sender 3FE Vacuum HOSE TOO ! FJ80 also - VintageTEqParts.com

NOS OEM Toyota Comes w/ a nice long section of OEM toyota Factory Vacuum hose also ! Valve, Bi-metal Vacuum...

vintageteqparts.com

Genuine NipponDenso / DENSO OEM JAPAN Gage Assy, Water Temperature Sender Sensor 2/76 - 92 FJ40 FJ55 FJ60 FJ70 BJ40 BJ41 FJ80 FJ62 Comes with OEM YAZAKI Repair Connector KIT & Special positive grip locking detent ball terminals 83420-20020 - Vint

PLUG and PLAY Repair KIT Genuine NipponDenso Japan Gage Assy, Water Temperature Sender 83420-20020 THIS IS : Gauge IN DASH SENSOR...

vintageteqparts.com

OEM GENUINE NipponDenso / DENSO 3FE PLUG and PLAY Repair KIT OE Sensor, sender Water Temperature (For E.F.I.) 89422-20010 Fits 88 -92 FJ62 FJ80 USA & Canada Spec. - VintageTEqParts.com

NOTE: This DOES NOT Come with the Wires Attached to the connector .... - OEM GENUINE NipponDenso / DENSO - DOES...

vintageteqparts.com

3FE PLUG and PLAY REPAIR KIT Cold Start Injector Thermal Time for EFI Timer Switch SENSOR Sender for Land Cruiser FJ62 FJ80 Pick-up 4Runner Fits 88 -90 FJ62 USA & Canada Spec. sensor sender 91-92 FJ80 89462-20040 - VintageTEqParts.com

NOTE: This DOES NOT Come with the Wires Attached to the connector .... Cold Start Injector Timer Switch SENSOR Sender for...

vintageteqparts.com

Where can I purchase the Cold Start injector time switch? for 1988 model. Thank you.

 

[lord2lord]

NO HEAT !

remove the upper housing

- use a old beach towel and clamp in a vice carefully

- apply moderate increasing force

- it should break loose

- if your sensor is fused and you cant remove it ,

- i have FULLY Restored 3FE Upper Housings TOP SHELF parts ..........

- my opinion :

remove what parts you need to to gain access to remove this thermo switch , when it breaks loose all at once , you can break other parts in the process .........


clear work area is a SAFE and low cost damage work area

you follow me here ?





View attachment 2759701

View attachment 2759708

Where can I purchase the Cold Start injector time switch? for 1988 model. Thank you

 

[diesellibrarian]

OEM Cold Start Injector Timer Switch for Land Cruiser FJ62 FJ80 Pick-up 4Runner

OEM Cold Start Injector Timer Switch for: '88 to '92 Toyota Land Cruiser FJ62, FJ80 with 3FE engine '88 to '95 Toyota pick-up and 4Runner Part # 89462-20040. Note: You must replace the female plug on an '88 vehicle using the supplied adapter kit, because the original switch for '88 is discontinued.

www.cityracerllc.com