Got my transfer case skid in this week. Will be installing and adding it to the rest of the skids this weekend.
E&E Off-Road 200 Series Skid Plate System (1 Viewer)
- Thread starter Tex68w
- Start date
This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.
teejnut
SILVER Star
Did my first oil change with the skids in place. Just had to remove the 4 bolts for each of the access points. It was easy access to the drain plug and oil filter. I have a Fumoto drain valve and use one of those adapters for the oil filter housings so no mess at all.
I also completed the TC skid install. I won't go into too much details since @Tex68w did a great write-up already! The TC frame bracket bolts weren't too bad once I got my extensions setup. I did the install in HIGH mode on the LX and for me it was easier to reach for these bolts with my feet facing the front while lying down on my back on a creeper.
Everything lined up great and the frame bracket and leg looks great and strong.
I also completed the TC skid install. I won't go into too much details since @Tex68w did a great write-up already! The TC frame bracket bolts weren't too bad once I got my extensions setup. I did the install in HIGH mode on the LX and for me it was easier to reach for these bolts with my feet facing the front while lying down on my back on a creeper.
Everything lined up great and the frame bracket and leg looks great and strong.
prwillard2
SILVER Star
Got my skids muddy and used today at Overland Expo West training.
Nice! Already missing a couple screws I see.
prwillard2
SILVER Star
I couldn't put them in after taking off the set once. Believe I may need to retap the screw holes.
No worries. I backed out one insert halfway on the trans skid when installing the transfer case skid. Didn't notice it until the next day because it was dark. Noticed after I took a pic and saw that it wasn't sitting flush in one spot. Because it's the first skid to go on, I had the pleasure of taking all of them back off to fix the insert. Then re- torque every skid screw again. That was fun and time well spent. I need to get a Makita battery powered ratchet to add to my tool set .
Gotta say it looks good though.
turbo8
Supporting Vendor
Agreed! He is such a good dude! Reliable, communicative and all around super helpful!
turbo8
Supporting Vendor
Thanks everyone I appreciate the feed back.
For the next batch I probably will adjust the front skid to allow more protection of the power steering cooler and the lower radiator. For those that already have the skids and are interested in this, you will get a very good deal.
This will also allow easier transition for filler plates to other bumpers. It will defiantly integrate nicely into my low profile bumper when I'm done.
For the next batch I probably will adjust the front skid to allow more protection of the power steering cooler and the lower radiator. For those that already have the skids and are interested in this, you will get a very good deal.
This will also allow easier transition for filler plates to other bumpers. It will defiantly integrate nicely into my low profile bumper when I'm done.
- Thread starter
- #172
Thanks everyone I appreciate the feed back.
For the next batch I probably will adjust the front skid to allow more protection of the power steering cooler and the lower radiator. For those that already have the skids and are interested in this, you will get a very good deal.
View attachment 3331535
This will also allow easier transition for filler plates to other bumpers. It will defiantly integrate nicely into my low profile bumper when I'm done.
View attachment 3331537
If we can make it work with my Dissent full bumper then count me in. I was thinking I was gonna have to make my own so hopefully this is a viable option.
That front bumper is looking great!Thanks everyone I appreciate the feed back.
For the next batch I probably will adjust the front skid to allow more protection of the power steering cooler and the lower radiator. For those that already have the skids and are interested in this, you will get a very good deal.
View attachment 3331535
This will also allow easier transition for filler plates to other bumpers. It will defiantly integrate nicely into my low profile bumper when I'm done.
View attachment 3331537
bloc
SILVER Star
I’m very interested in this development.Thanks everyone I appreciate the feed back.
For the next batch I probably will adjust the front skid to allow more protection of the power steering cooler and the lower radiator. For those that already have the skids and are interested in this, you will get a very good deal.
View attachment 3331535
This will also allow easier transition for filler plates to other bumpers. It will defiantly integrate nicely into my low profile bumper when I'm done.
View attachment 3331537
teejnut
SILVER Star
I'm interested. I still have my Dissent filler piece I need to use.Thanks everyone I appreciate the feed back.
For the next batch I probably will adjust the front skid to allow more protection of the power steering cooler and the lower radiator. For those that already have the skids and are interested in this, you will get a very good deal.
View attachment 3331535
This will also allow easier transition for filler plates to other bumpers. It will defiantly integrate nicely into my low profile bumper when I'm done.
View attachment 3331537
turbo8
Supporting Vendor
Don't worry, when I said very good deal, that means free.
abawockee
SILVER Star
Amazing, amazing, amazing seller is all I can say! Thank you for helping me be a "responsible" adult, and answering all my questions!Don't worry, when I said very good deal, that means free.
Hopefully I'll get to install all my skids this weekend, barring no issues or hail/hurricanes/tornados!
Don't worry, when I said very good deal, that means free.
Well that's pretty darn cool
Haven't had a chance to install the skids this past weekend, but making some time over next 
Will add some photos once installed.
Will add some photos once installed.
