Look up detroit speed. did an ls swap a few years ago. think they have fitting to convert to metric stuff
Builds BurntToast's FJ62 Build "Hoss" (17 Viewers)
- Thread starter BurntToast
- Start date
-
- Tags
- fj62
This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.
- Thread starter
- #322
Figured out the power steering, will be picking up a m14 banjo to an6 adapter for the box.
helped a friend with more 302 fun. Thing is going to get a turbo.
Busted my toe but managed to throw the dissent bumper on for fun
helped a friend with more 302 fun. Thing is going to get a turbo.
Busted my toe but managed to throw the dissent bumper on for fun
That bumper looks awesome. What color you going with? And do I remember that you said somewhere you’re going to paint your rig, too?
- Thread starter
- #324
Not sure on color, but black/grey ish. Maybe cerakote, maybe just steel-it.
I do plan to paint the truck, but ill do it last, after all the mods are done
Nice. Can't wait to see it all come together.
- Thread starter
- #326
Bits and pieces from @cruisermatt and @TRAIL TAILOR
These are supporting future speedhut gauges and the DBW
Nicely machined parts
Yes that washer holding the intermediate shaft in is wrong. She seems to have disappeared in the rebuild
These are supporting future speedhut gauges and the DBW
Nicely machined parts
Yes that washer holding the intermediate shaft in is wrong. She seems to have disappeared in the rebuild
- Joined
- Jul 22, 2012
- Threads
- 578
- Messages
- 16,283
- Location
- Winter Park, Florida
- Website
- www.cruisermatts.com
You should have mentioned! I would have thrown one in with the parts. I have plenty of them new and used.
- Thread starter
- #328
I didn’t remember until I put your speedo plug inYou should have mentioned! I would have thrown one in with the parts. I have plenty of them new and used.
- Thread starter
- #329
Finished up the PTFE lines for the fuel. Went with a fixed pressure regulator from Radium. Has a drop in Bosche regulator. Reasons include apparently the “corvette filter regulator” is widely counterfeited and hard to find a real one. So I went discrete on filter and regulator
Just needs some adel clamps, .500” I have are slightly too large. Hose OD is .450”
test fit the LSPV replacement. Got this on with adapters from FlyingMiata, but I found something similar at CityRacer after it was ordered.
I am designing a 3D printed bracket for the valve to master cylinder. Going to have to be ASA for under hood heat. That might not even be enough
Just needs some adel clamps, .500” I have are slightly too large. Hose OD is .450”
test fit the LSPV replacement. Got this on with adapters from FlyingMiata, but I found something similar at CityRacer after it was ordered.
I am designing a 3D printed bracket for the valve to master cylinder. Going to have to be ASA for under hood heat. That might not even be enough
tmxmotorsports
SILVER Star
Don't forget to put a check valve on that brake booster vacuum line.
tmxmotorsports
SILVER Star
I've been looking for nice an line clamps that can be mounted to the chassis or body haven't really found anything that I like yet and ptfe lines are smaller that regular an line.
- Thread starter
- #332
My man, thanks for the reminder
- Thread starter
- #333
the OD is basically 7/16" which is annoying. Everything is 3/8 ID or 1/2 except for a few Sandvik Marine ones but they aren't cheap
- Thread starter
- #334
Wrapped up the brake union underneath the truck and 3d printed a test bracket
Got the trans cooler installed to the center support, using some VHB for wear isolation between the two parts and bolted in place
Got the trans cooler installed to the center support, using some VHB for wear isolation between the two parts and bolted in place
- Thread starter
- #335
@tmxmotorsports found the p-clips. MS21919 Wch Clamps | Aircraft Spruce - https://www.aircraftspruce.com/catalog/appages/ms21919clampswch.php
The Mil-spec covers 7/16"
The Mil-spec covers 7/16"
tmxmotorsports
SILVER Star
Man I really need to get a 3d printer and figure out how to use it . I've seen those kind of clamps I'm looking for something more high end maybe even 3d printed lol
- Thread starter
- #337
Love my 3d printer for stuff like this that isn’t critical
tmxmotorsports
SILVER Star
That's what I'm saying little bracket things that I would beat myself up on making out off metal.
tmxmotorsports
SILVER Star
I'm not all that computer savvy tho.
- Thread starter
- #340
Fusion360 is free and has solid tutorials online, give it a look
