Builds Benjamin’s 3D Prints Build (7 Viewers)

[prwillard2]

Heres my Switchpro panel installed into a dirty ass surround


View attachment 2646175

What item is that attached to?

 

[blackohio]

Make 35: Switch Pros SP-9100 Switch Panel Mount

1. Overview of the Final Product

View attachment 2382728
View attachment 2382729
View attachment 2382722


2. Introduction

M35 mounts a Switch Pros SP-9100 Switch Panel in the overhead console. It is mounted through the four screw holds on the back.

View attachment 2382727

3. Purchase

Four stainless steel screws are included.

$50 + Shipping (USPS Priority). PM for direct Paypal payment.

 

[BenCC]

i'm definitely down for this... SAEDOT Fogs for me too to replace my factory fogs running in a TJM bumper! if i can get a 2nd light for flood/ditch, that would be a bonus, but I'll take what I can get!

A TJM fog is on the way to me.

 

[Windknotz]

A TJM fog is on the way to me.

I'm about to make some adjustments to my ARB bumper, and need to remove the fog/signal housing to do so. Do you want me to send one to you to play with?

 

[BenCC]

I'm about to make some adjustments to my ARB bumper, and need to remove the fog/signal housing to do so. Do you want me to send one to you to play with?

Do you want to put rigid industries D2 or Baja Designs Squadron in there?

 

[Windknotz]

Do you want to put rigid industries D2 or Baja Designs Squadron in there?

I don't, but someone earlier in the thread had asked at one point I believe. I'll make mine available to you if you need it.

 

[Derphound01]

I apologize if this has already been covered - I haven’t read the entire 64 page thread

Do you know if the overhead console mounts that replace the sunglasses holder will fit a GX470? Specifically the M1, M4, M5.

I can get dimensions if that helps
View attachment 2351323

First post on the forums for me. I joined solely because of this thread.

I read through the whole thread looking to see if anything had been done with the GX console and did not see anything. I'm looking to find something that will accommodate either a row of the Toyota tall switches, or my SiriusXM faceplate with a Toyota tall switch on either side of it.

If you're wanting to experiment with one, I can gladly mail you mine.

 

[GRunner]

I am still trying to buy a used unit on eBay. Didn’t find one.

I have a factory one I can send for prototyping. Let me know if you want.

 

[dcashley84]

Can the remote face plate that replaced glasses holder be used for other radios or just the 2 specific ones listed. Both radios are pretty Spendy

 

[yotanewb]

Ben, I am interested in the switch mounts that are in the change pocket on the center console just to the left front of the shifter. I’ve searched the thread but can’t find it. Can you tell me which Make that is?

 

[BenCC]

Guys, it has been a pleasure

I have a factory one I can send for prototyping. Let me know if you want.

I will put a pause to this project. Sorry. But I will ask you know when I need it. Thanks.

 

[BenCC]

Can the remote face plate that replaced glasses holder be used for other radios or just the 2 specific ones listed. Both radios are pretty Spendy

All the radio mounts are for specific faceplate. Let me know what unit you have.

 

[BenCC]

Ben, I am interested in the switch mounts that are in the change pocket on the center console just to the left front of the shifter. I’ve searched the thread but can’t find it. Can you tell me which Make that is?

Sorry for the late response. It is an variant of Make 6. PM please.

 

[BenCC]

A TJM fog is on the way to me.

Update on the TJM foglight mount

The foglight slot on TJM bumper is 2 inches tall. The Baja Designs S2 is the only decent LED pods that I can find that fit that space.

 

[CBdeJ]

This is a TJM T13 fog….

Is it possible you have the running light/turn signal light?

if you want me to send you one of the lights pictured above, I can. I replaced mine with Stedi LEDs

 

[Roosevelt T]

Update on the ashtray replacement

View attachment 2528049

Hey Ben! Looks like things are going great in this thread. Even more cool stuff than last time I checked it.

Are you still working on an ashtray replacement?

 

[BenCC]

Hey Ben! Looks like things are going great in this thread. Even more cool stuff than last time I checked it.

Are you still working on an ashtray replacement?

Intermittently haha. I need help. Is it possible to get the pieces where the ashtray goes in? It seems one of the pieces is pretty large.

 

[BenCC]

This is a TJM T13 fog….View attachment 2664459

Is it possible you have the running light/turn signal light?

if you want me to send you one of the lights pictured above, I can. I replaced mine with Stedi LEDs

Is this for different TJM bumper? What is the diameter of the pictures light?

 

[CBdeJ]

Is this for different TJM bumper? What is the diameter of the pictures light?

The light above fits a T13 bumper. The diameter is about 3 1/4 inches

 

[BenCC]

The light above fits a T13 bumper. The diameter is about 3 1/4 inches

I see. What do you need me to do with it?