boot

I did an oops and tore the boot for my transmission shift lever. My truck is a 1982 FJ60. Anybody out there got one for an early truck? Would prefer it ASAP as I daily this thing and the noise in the cab is extra loud with the 1” hole! EDIT: This thread turned into a tech discussion. For...

I nicked my cv boot. I tried to put a split boot from a 4Runner on but it’s too stiff and pulls off the wheel end in a tight turn. Has anyone tried one that works? I’d really rather not pull the axle

Sold my 100 series, No longer need PN - 04427-60120 $110 + shipped USA For both Paypal Friends and family or you pickup the 3% OBO

I have a torn steering rack boot on my 06 LX can I change it without unscrewing the tire rod end?

Hi all. Looking for advice on what to do about the CV Boots I saw leaking on my 2008 4Runner, 132k miles. See photos. Axle with the "CPTD" is passenger side and was replaced by dealership in 2019 when they said the original was leaking. The other/driver side (bottom photo) is original axle...

. https://vintageteqparts.com/collections/everything-else-hardware-fsms-shop-manuals-special-teq-stuff/products/dor-early-fj40-4wd-indicator-switch-refresh-restore-and-updated-rubber-weather-boot-kit-form-everything-you-need been plugging away at this for a bit now , ever since the HERITAGE...

Had this on my 3FE for a minute. Decent shape. $60 shipped lower 48 or $40 San Diego local pickup.

I recently replaced the shocks and coils on my LC 100 (220k miles), and also raised the torsion bars a bit. After doing so, I just found that both sides of my CV boots are leaking between the axle and the boot - the clamps aren't tight enough at the angle they're at. Both are leaking through on...

This is the boot for Gear Reduction starters with 20mm OD insulator ring, aka 28100-60070-84. The insulator boots I’ve found for sale don’t actually fit the insulator ring because they are 30mm, which wasn’t acceptable to me for this starter. $20 shipped each. 9 available.

I have two (2) sets of brand new Toyota intake boots for the 3FE 80 series. I originally ordered them from a well known west coast parts supplier but they showed up WAY late, so by the time I finally received them I had already installed a set from some where ells. I'm also not sure why I got...

New left and right defrost tubes and inlet duct boot, all clean, soft . Used duct, vent cover screen. And working Vent open close cable. 1968-72 FJ40 $500.00 plus shipping.

https://vintageteqparts.com/collections/everything-else-hardware-fsms-shop-manuals-special-teq-stuff/products/copy-of-non-usa-oem-toyota-yazaki-japan-spec-b-positive-n-negative-battery-terminals-including-special-red-factory-flexible-terminal-boot-overhaul-repair-restoration-all-inclusive-plug-an...

Need for H55 swap. Thx. like this one...

( NEW PRODUCT RELEASE ) NOS General Service / Room Lamp Switch W/ OEM Protection Boot & OEM 2pin Rubber Bullet Kit 84270-60010 / 84270-60020 / 84270-60030 Note : does not include wire itself …. Fyi NOS General Service / Room Lamp Switch W/ SNOW VERSION Insulator Protection Boot &...

I have a lifted 07 limited sequoia and need to replace my inner cv boots. I was going to go with a high angle cv boot but wanted to see if anyone could reccommend a brand or is it best to stick with oem? Thx.

I'm rebuilding the front wheel cylinders and everything is good except the rubber boots that fit on the adjuster pistons. The rebuild kits I got have the rubber cup and boot for the piston side, but didn't include the boot for the adjuster side. I've searched online and haven't had luck...

Upper ball joint boots were shot (314K miles) and I bought the kit at the Toyota dealer ($15 list price, each) and installed it while replacing the CV axle. Very straightforward, but the new 'clip' included with the kit (the slinky-like boot retainer) is mild steel, and very flimsy and instantly...

When compressing the pistons to install new pads, some of the boots got folded out/unseated. I tried sticking it back down but couldn't get it all the way. Perhaps I need a different tool. The best thing I could think of that I figured wouldn't damage the boot/seal was the small red tube that...

It looks like I tore my passenger upper cv boot yesterday. It flung out a bunch of grease. It’s torn at the small end first bellow. I’m tempted to clean it as best I can and wrap gorilla tape around it to try to keep grease in. It is driving fine with no clicking/issues. Any other ideas? Salida...

The attached .pdf file shows the vinyl or leather pattern to replicate the original e-brake boot. This was one of the last items for my interior restoration and I had the upholstery shop that did my seats use the same leather for my boot. The gave me the old panels so it was easy to trace them...