What have you done to your 100 Series this week? (39 Viewers)

[zgfiredude]

I've been running those for 5+ years on both 100s, so for the price, the longevity is great!

Just ordered these, thx!

 

[Zuberg]

Question, does anyone know what the little plastic plugs that the OEM screw goes into on the fender lip?

Just realized the other side is missing them

might be looking for these

ran rokblokz on the wife's subaru for few years. they held up quite well w/ a fair amount of gravel road travel.

 

[Unrulykid]

I have a spare tire winch thingy somewhere in the garage but no key. Happy to give a way to some in need. Not sure the key is more than $49 at the stealership

It is easy to remove the key from the spare tire carrier… see this thread…

B

Thread 'Removing Spare Tire Winch Anti-Theft Key'

Aug 27, 2019

Saw a post whereby someone was looking to remove the anti-theft bud/tulip/lock on their spare tire winch. Despite cleaning mine annually, the tulip started to strip as the tire approached the top, making it very difficult to snug it up. At least the tire comes down, but going up it was starting to rattle/bounce around. The last thing we need is to have spare tire removal issues when we need it most.

Anyway, here are some pics on how to remove the anti-theft part and just use the hook tool in your tool kit in the existing slot. ie, go back to a non-anti-theft. Stick it in a...

• BoneCollector
• Replies: 5
• Forum: 100-Series Cruisers

• 

 

[Asanka]

It is easy to remove the key from the spare tire carrier… see this thread…

Great, whoever wants it, it is just shipping cost.

 

[Wagoncruzer]

I installed 555 inner and outer tie rods with some new rack boots. Did the alignment by myself with a tape measure! Then had my buddy laser align it and it was almost dead on with my tape measure.

 

[TRAIL TAILOR]

 

[Hoserock]

In need of assistance. I purchased the SAE Rigid fog lights to go with my front bumper. The lights come with Deutsch connectors almost same as the fog lights on the car. I was hoping it would be plug and play without the need for the harness it came with. The two connectors don’t seem to mate very well. Can anyone tell me if I would be able to cut the male end off the rigid harness and splice it into factory harness so I can control the fog lights from the factory knob on the steering column. The factory wires look to be a thinner gauge than the Rigid harness. Thanks.

 

[costahh]

In need of assistance. I purchased the SAE Rigid fog lights to go with my front bumper. The lights come with Deutsch connectors almost same as the fog lights on the car. I was hoping it would be plug and play without the need for the harness it came with. The two connectors don’t seem to mate very well. Can anyone tell me if I would be able to cut the male end off the rigid harness and splice it into factory harness so I can control the fog lights from the factory knob on the steering column. The factory wires look to be a thinner gauge than the Rigid harness. Thanks.

Pretty simple, I ended up cutting off the factory plug and wiring in a Deutsch connector to mate to the aftermarket lights, in my case Diode Dynamics. Works with the stalk factory fog light switch took all of 15 minutes. I ordered the crimper and Deutsch kit off amazon I can link in what I used if you are curious

 

[whitec13]

View attachment 3971509

You crazy bastard, you actually beat me to it lol. This was my plan for Blue when she is retired. Except slightly different. Pretty much the same though. Crazy job and good job being crazy!

 

[Hoserock]

Pretty simple, I ended up cutting off the factory plug and wiring in a Deutsch connector to mate to the aftermarket lights, in my case Diode Dynamics. Works with the stalk factory fog light switch took all of 15 minutes. I ordered the crimper and Deutsch kit off amazon I can link in what I used if you are curious

Yes please, no issues with the difference in wire gauge? The stock harness can handle the load?

 

[costahh]

Sent you a PM