What Did You Do with Your 80 This Weekend? (166 Viewers)

[SeaDrifter]

Got it painted
View attachment 1090801 View attachment 1090802 View attachment 1090803 View attachment 1090804

Paint looks really nice!

 

[80seriesnut]

I would love to have my 96 and 04 repainted. I took the 04 to a place and they quoted me 95 hundred bucks. That's crazy

 

[LS1FJ40]

Is this why my sliding windows leak? It appears that the rubber has shrunk. Could I just "seal" this joint temporarily?

 

[NLXTACY]

Is this why my sliding windows leak? It appears that the rubber has shrunk. Could I just "seal" this joint temporarily?

View attachment 1091018

I think you are missing a clip

 

[LS1FJ40]

I think you are missing a clip

I'm missing it on both sides... ugh.

 

[NLXTACY]

No, maybe I'm wrong. Maybe it is shrinking. Take a look at both sides of mine. Different size gaps. Or that's in addition to a missing clip?

 

[NLXTACY]

I'm missing it on both sides... ugh.

If so, so am I

 

[Parsnip]

I think you are missing a clip

+some RuGlyde on a throw-away paint brush will clean up and lube that seal.

 

[LS1FJ40]

View attachment 1091040 View attachment 1091041 No, maybe I'm wrong. Maybe it is shrinking. Take a look at both sides of mine. Different size gaps. Or that's in addition to a missing clip?

Is the spider OEM or aftermarket?

 

[retrofive]

Is this why my sliding windows leak? It appears that the rubber has shrunk. Could I just "seal" this joint temporarily?

View attachment 1091018

It was in the pool!

(I think shrinkage as well, have the same thing going)

 

[LS1FJ40]

I'm thinking some non-silicone based sealant is going to get applied to that gap. See what happens. I'm getting a small amount of water in during hard downpours (or washings). There is definitely some shrinkage going on because you can see it in the corners but it isn't pulling away from the metal. I suppose I could actually water test it to see...

 

[NLXTACY]

Is the spider OEM or aftermarket?

No, I think thats a bee that got swooped up during one of my 90MPH drives that...oh wait...you don't know what that means. See when you don't have a 3FE you can drive over 70 and...

 

[LS1FJ40]

No, I think thats a bee that got swooped up during one of my 90MPH drives that...oh wait...you don't know what that means. See when you don't have a 3FE you can drive over 70 until your head gasket blows or you have to replace your PHH or you have to replace your wire harness because it's melted or...

FIFY

 

[pilotuku]

Since my 4x4labs install, we had to cut the OEM tail pipe and replaced it with this temporarily...

 

[LS1FJ40]

No, I think thats a bee that got swooped up during one of my 90MPH drives...

I'm sure there is a lot of 90 mph driving in this...

 

[NLXTACY]

I'm sure there is a lot of 90 mph driving in this...

View attachment 1091045

The key is staying away from that

 

[azcrackshot]

Did a little trip up North East of Phoenix. Weather was perfect and the Cruiser ran flawlessly.

 

[cleetus]

In Colorado, heading up to the grand mesa for a family reunion. Lots of rain.

 

[zona]

Did a little trip up North East of Phoenix. Weather was perfect and the Cruiser ran flawlessly.View attachment 1091079
View attachment 1091080 View attachment 1091082
View attachment 1091081

I was told that D rings in the front of a LC is unacceptable--I'm just the messenger--only Jeeps keep the D rings in front due to the need of being pulled out. Just kidding, I love your rig!

Zona

 

[LS1FJ40]

I did my EGR and VSV delete over Memorial Day weekend. I didn't have the proper M26x1.50 plug and couldn't find one anywhere. Well, guess what? I replaced the make shift EGR plug (see the red dot, that's FIPG sealing the metal disc inside the nut)

With the proper hex head plug (Dorman 090-099, which is unobtanium but I procured through the generosity of a fellow MUD member).