My list also breaks dopwn between summer-only vs. winter-optional tasks since the truck lives outside. Can't paint in winter. Maybe not so much an issue in Brisbane but maybe the wet season impacts schedule.
What did you do with your 60 this weekend? (17 Viewers)
- Thread starter MrMoMo
- Start date
This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.
Haha well hope it wont take seasons!
- Joined
- Jun 21, 2011
- Threads
- 230
- Messages
- 21,732
- Location
- Redding, California
- Website
- trail-tailor.com
Applied a new top coating to @DougRFJ62 rig. Really like this material. Will be my go to from now on.
J
J
Did my Knuckles this weekend (and last) took time to get all of the years of crap off of everything and then repaint. What do you all think of the wear seen in the pics?
Raptorliner?
Spent 3 days on the GA Traverse, including one POTA activation, then attended a ham fest. These photos are day three.
My POTA GO BOX was dead so I hooked up my radio to the main battery in my 60. I have the Power Pole plugs connected to my main battery to connect a trickle charger when needed.
My POTA GO BOX was dead so I hooked up my radio to the main battery in my 60. I have the Power Pole plugs connected to my main battery to connect a trickle charger when needed.
Nice fall weekend.
Really nice shot !!!!!
Scuffs on the outside of the birfield joint don’t influence anything. It’s the innards with the balls that’s the significant wear point
Exploring Utah's natural diversity.
30 min. North and 30 min. South of Zion in the same day. From 10k to 3k feet in altitude. Just incredible.
30 min. North and 30 min. South of Zion in the same day. From 10k to 3k feet in altitude. Just incredible.
Gretsch
SILVER Star
Quick Run this weekend to a local State Park. Met my Brother and family down from Philly for a nice couple days of camping. My son came down with our Motorcycle as well. Was a good time and nice reset from the daily grind. Simple trip and close by but was enough for a much needed recharge. The old girl did great.
Last edited:
Painting mine is on the list but its way way down the list haha.
Now that my 60 can travel at like normal speeds i am noticing a ton of new noises that were once masked by the sound of my super loud 2F with headers. There seems to be a ton of wind noise at the driver and passenger windows. It seems like its coming from the very front of the windows where it comes to a point like above the side view mirrors. I have the window runs replaced and the felts replaced. Does anyone else have this noise? My door seals look to be okay but will replacing these as well remove that noise?
Im also Trying to track down some drivetrain vibration issues now too. The extra power seems to have shown the age of my rear axle. I rebuilt the T case when installing the advance adapter but itseems to be making a high pitched noise that is throttle dependent. Very light throttle at cruise has it whine, and then stops when i let off. Going to go out and remove my driveshaft and see if it does it without a drive shaft. I am hoping the vibrations and noise are coming from my rear axle because i have a fzj80 axle waiting to go in and i can rebuild that one with new bearings and just live with the racket and vibrations until thats installed. Anyone have any similar problems after an LS Swap? Pinion angle and output flange are within 1* of each other so i doubt its driveline angles
Im also Trying to track down some drivetrain vibration issues now too. The extra power seems to have shown the age of my rear axle. I rebuilt the T case when installing the advance adapter but itseems to be making a high pitched noise that is throttle dependent. Very light throttle at cruise has it whine, and then stops when i let off. Going to go out and remove my driveshaft and see if it does it without a drive shaft. I am hoping the vibrations and noise are coming from my rear axle because i have a fzj80 axle waiting to go in and i can rebuild that one with new bearings and just live with the racket and vibrations until thats installed. Anyone have any similar problems after an LS Swap? Pinion angle and output flange are within 1* of each other so i doubt its driveline angles
Zjohnsonua
SILVER Star
Slight facial rearrangement. I couldn't do this again if I tried.
LazarusTaxa
SILVER Star
I did this over the weekend:
Hopefully this doesn't spiral too much further out of control
Hopefully this doesn't spiral too much further out of control
Hopefully it does, you gotta put that crap back together lol.I did this over the weekend:
View attachment 2833431
View attachment 2833434
Hopefully this doesn't spiral too much further out of control
Dammit man! You're like a wizard or something!
MAn...your dash looks sooooo clean. I haz dash envy!!!!
