WOW!! Where at?
What did you do with your 60 this weekend? (75 Viewers)
- Thread starter MrMoMo
- Start date
This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.
WOW!! Where at?
Blain's Farm and Fleet. The signage in the store said Diehard but it's definitely not the same battery that Sears sold.
Attempting oil pan gasket replacement due to leak!
Got Pan off using the jack and 2x4 method.
Painted pan.
Now trying to figure out an easier way to remove the gasket on the arches!!
Used a screwdriver and heat gun on the back, what a chore! Now doing the front! got to be an easier way!
T
Got Pan off using the jack and 2x4 method.
Painted pan.
Now trying to figure out an easier way to remove the gasket on the arches!!
Used a screwdriver and heat gun on the back, what a chore! Now doing the front! got to be an easier way!
T
Broke the winter sickness and got out for a wheel...
I made a thing to hold my microphones out of an old street sign.
Desmogged! Replaced power steering cooler! Resurfaced manifold! Never idled so low, ran so quietly. I'm a very happy camper.
Replaced the gauges with Speedhut gauges.
MountNGoat
KK6WRY. Always Learning
Completely lame compared to what most post, but I got my starter back in after it was discovered there was an internal ground issue. Now she fires up and I got to take her for a spin around town today. No wheeling, but I didn't care, just happy to be behind the wheel today!
Pics?
Last edited:
- Joined
- Jul 22, 2012
- Threads
- 577
- Messages
- 16,191
- Location
- Winter Park, Florida
- Website
- www.cruisermatts.com
Drained the ballast!
Check your rear 1/4 panels guys, each of mine had a couple gallons of water.
Check your rear 1/4 panels guys, each of mine had a couple gallons of water.
Tore transfer case off transmission earlier in the week and ordered parts (transfer rebuild kit, clutch slave cyl.,clutch slave cyl. hose, brake master cyl., both front and rear out put flanges they should be in the 3rd from cruiser outfitters, yesterday pulled head light bezels, grill, a/c condenser, radiator, fan, thermostat, a/c idler bearing, metal coolant lines, belt set, and all hoses and battery tray and a lot of small items Onur is getting that stuff. Will be building idler bracket where smog pump was today.
Its actually a 82 and I don't own it, I just work on it. Its my uncle's I've been busted. But I want one does that count? I really don't know it doesn't have one now.
- Joined
- Jun 21, 2011
- Threads
- 230
- Messages
- 21,746
- Location
- Redding, California
- Website
- trail-tailor.com
Tuned up a 3FE with new plugs, wires, rotor button, distributor cap. Checked the valves and all were in spec. Toughest part is reinstalling the valve cover without dislodging a new gasket but a little silicone in the groove helps to tack the gasket in place. This 3FE has > 200k miles on it and the upper end is sludge-free. Been running Rotella in it for ca. 100k miles.
USOffRoad
Supporting Vendor
Drove my ' new' 62 home to Texas from Louisiana.
I replaced my alternator belt when I noticed that it was starting to fray.
Didn't do anything major this weekend, but I did scout some sand dunes. In two months I can roam the beaches again down cape, anybody getting sandy neck OHV permits??
Next weekend ill do the transfer case compression spring and try to hunt an electrical grimilin in my quad gauge cluster.
Next weekend ill do the transfer case compression spring and try to hunt an electrical grimilin in my quad gauge cluster.
