Tripledave
SILVER Star
Follow along with the video below to see how to install our site as a web app on your home screen.
Note: This feature may not be available in some browsers.
This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.
Not that I've heard. If you care to explain how that solved the issue, I'd love to learn about how and why however.Is part time available for the 200 yet? I solved the torque steer issue on the 100 series with part time.
Not that I've heard. If you care to explain how that solved the issue, I'd love to learn about how and why however.
Nothing while braking. Perfect. I even inspected the brakes after returning home from Colorado just to be sure I had plenty of pad life after driving in the mountains. I actually have to hold the wheel to the left a bit to keep straight under acceleration. Wheel stays almost perfectly straight on a flat road while cruising and/or braking. I'm far from an expert on alignment but I am quite familiar with mechanical engineering and it seems to me like even a slight lateral offset acted upon by the squat of weight transfer to the rear axle assembly would cause an effect on the trajectory of the vehicle. Maybe even amplified by the front wheels being driven as well. Anyone more familiar with vehicle alignment who can make more sense of the specs I've attached please explainThere was a similar case here in Phoenix last year. Turned out to be the steering assembly getting worn, and causing bad torque steer and pulling to one side when braking.
do you notice any pull in one direction or the other when braking?
does the wheel pull to the right and stay there or snap back?
That certainly makes sense. Perhaps a diff drop could partially remedy this issue as well? Part time would be great though, MPG may even improve a tick or two. Never really loved the idea of full time 4wd, I like the option to decide when and if I need 4wdIn my case and many others torque steer is caused by the increased angle of the CV axles. With Part time CV axles are not driven or turning.
98kHow many miles were on the truck before you lifted?
I've fixed torque steering issues on a couple LCs, my 200 being one of them. I agree with @TexAZ that a good possibility is your steering linkage has worn itself into an angle that is now much different because the lift, changed the angles.
For my personal 200, the front right tire was compromised from ply steer, but since the owner just accepted it for tens of thousands of miles, it wore in the outter ball joints to also create a pull. New tires helped, adding camber to left side help with road crown, replacing outer tie rods was the real issue along with the bad tire.
I an effort to save you money from replacing unnecessary things, I would first start off by saying that Slee set up your alignment for very flat roads, if you live in an area where the roads have a good crown to them, that truck is going to always pull right. But they don't know where you are going to drive, so I can't blame them, just something to keep in mind.
Also, your rear end is not causing any torque steer (I could go into that more if you want)
If it was me I would do this, in steps, and stop at each step if it works:
1) Swap your front tires left and right, see if you pull the other direction, I'm sure it isn't this, but it should be the first thing you do.
2) have Slee or any alignment shop add +.5 degree of camber to the front left wheel.
3) replace outer tie rods $40 each for OEM, (inner tie rods is you have the money, $200 each for OEM)
If you don't have the ability to do it yourself, just let me know.
Here are the stock alignment specs:
Front Caster
2.9±0.75
Front Camber
0.13±0.75
Front Toe (degrees)
0.24°±0.16°
Front Toe (inches)
0.12±0.08"
I did +1 degree added camber to my front left, so +1.1 front left, +.1 front right.
Was perfect for Texas and Georgia road crown after I replaced tie rods.
But yea, I say it was old steering linkage that was happy where it was, now it's not where it was, so it's not happy. I know it sounds trivial, but I can make you car the most unsafe thing in the world, with a couple specific changes to your alignment cams, know that very small changes, make very big changes in feel.
Anytime man, we all are constantly learning, and I doing so, and we all find our own way to tackle issues. At the end of this, you should be aligning like a champ.As I read this I am reminded once again of the wealth of knowledge that is simply a question away. Before I even start to address these issues, please accept a thank you for taking time to explain with real data and experience.
As I do live in Texas, the roads are indeed crowned quite steeply in most areas. Dallas/Ft Worth to be specific, too bad (or good for you) you're not local or we would definately be discussing/testing this in person. Thanks for the offer sir.
I am noticing different wear patterns on my front tires also as I stare at them while typing.
98k on the truck when the work was done, definately wear to the outer if not the inner tie rods as you said. Shouldn't be a big deal to change outer rod ends like you said.
I'll start experimenting and changing items in the order suggested. Once I get the outer rods replaced, should I go back to factory alignment specs plus .5deg camber on left front until it feels right or should I simply have the shop add +.5deg camber to left front leaving other settings alone?
Which brings me to another question...... Anyone know of alignment shops in DFW that are trustworthy and knowledgeable enough to align as needed?
Thanks again Taco
Sure thing. Torque steer is caused by more torque being delivered to one side of a car than the other. It is common in front wheel drive cars that have unequal drive shaft length, like our front ends. But the rear end of our trucks have equal length shafts, in fact the 200 series is the first land cruiser to have equal length rear shafts. 100 series and before had varying different lengths of left and right rear drive shafts. So that is why the REAR 200 axle CANNOT create torque steer.Hey @Tripledave, did you ever resolve this? I have a very similar pull with my newly lifted 200. In my case I need to hold the steering wheel slightly to the left (at about the 11:30 mark) when going down the road, but under acceleration it pulls to the right, and when letting off the gas I'm pulling back to the left.
I need to swap the rear springs so I'm hopeful this clears up after I swap them (and hopefully the truck is level again) but I have a suspicion there may be something else at play here. (FWIW I have about 1.25-1.5" of cruiser lean in the rear and 0.75" in the front... Tough Dog said to put the taller spring on the driver's side, which I did, but the taller OEM Toyota spring was on the passenger side so I think for the 2013 model year they were incorrect)
@Taco2Cruiser, can you elaborate on "Also, your rear end is not causing any torque steer (I could go into that more if you want)"? Or at least can you describe how you would know if you did need a rear panhard rod?
Did that mean the taller one when on your passenger side?I know for my 200's Tough Dog setup, I put the springs on the side as they were labeled and I have no lean. Keep in mind, however, I have heavy springs.
Did that mean the taller one when on your passenger side?
I had a little bit of lean with the front right low, but it was my rear left shock was set 20 psi more than the rest, all good now that I put my fronts to 300psi and the rears to 305 psi.
What were they labeled? A and B or something like that?I didn't note a size difference. Not saying there wasn't one, I just didn't notice and went with the labeling.
What were they labeled? A and B or something like that?