Tap and die set

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Joined
Feb 27, 2006
Threads
124
Messages
1,225
Location
God's Country
Looking to get a nice tap and die set. Need to know a good one. Craftsmen, husky, etc. Mainly for the resto of my '75
 
I have the beginner standard and metric sets from Craftsman. Works for 90% of what I need to do with the addition of some pipe taps. I haven't had one get dull or break yet, and I've had them for several years.

Mcmaster has some pretty exhaustive sets, MSC has plenty, all the cheaper tool suppliers will have sets (Northern etc).

It's for hobby use, so I wouldn't spend the bucks on Snap On, Matco etc...
 
I have the beginner standard and metric sets from Craftsman. Works for 90% of what I need to do with the addition of some pipe taps. I haven't had one get dull or break yet, and I've had them for several years.

Mcmaster has some pretty exhaustive sets, MSC has plenty, all the cheaper tool suppliers will have sets (Northern etc).

It's for hobby use, so I wouldn't spend the bucks on Snap On, Matco etc...
10-4 , I already bought a craftsmen set today, just wanted to weigh in.
 
I too, would like a better set than the ones I picked up in Autozone 10 plus years ago on a despirate late night auto store run. I'm subscribing.
 
I just have a kit from Sears and a bunch of other ones (typically they cost half the price the kit did) for specific duties..

So far they all work well..
 
I have the Harbor Freight garbage, but they've done what they needed to do. Can anyone tell me what the differences might be between those and a good quality tap or die? I expect longetivity would be an issue, and perhaps breakage, but I haven't seen any reason to upgrade yet. They get very occasional use, and it's nice to have a big selection on hand rather than having to run out and buy each individually when needed due to cost. I've never used a high- or medium- quality tap or die, so I might be missing something. Or maybe not, as I mostly use them to chase existing threads.

-Spike
 
I have the Harbor Freight garbage, but they've done what they needed to do. Can anyone tell me what the differences might be between those and a good quality tap or die? I expect longetivity would be an issue, and perhaps breakage, but I haven't seen any reason to upgrade yet. They get very occasional use, and it's nice to have a big selection on hand rather than having to run out and buy each individually when needed due to cost. I've never used a high- or medium- quality tap or die, so I might be missing something. Or maybe not, as I mostly use them to chase existing threads.

-Spike

I bought a HF tap and die set for trail use. I have used a few of the taps and dies from this without issue. One day I pull out a die and discover that it was manufactured crooked. I mean really bad. If there was any quality control this would have been caught. With HF tools you often get what you pay for.

I also have a Craftsman set for the garage. I don't think you can beat the Craftsman for price / quality. If you want to spend some big money look up what some of the coated sets that MSC and the other houses sell for. :eek:
 
I have the standard Snappy set , cuts pretty nice and clean.

As stated before the Craftsman sets are a great deal for the $$.

ken
 
I have a craftsman set been quite happy with it,

I have used cheaper taps, only difference I have noticed is the number of flutes, the 3 and 4 flute variety seam to cut better than 2.
 
I threw my HF set in the trash. Like John said, NO quality control at all.
 
Irwin here. So far appears to be excellent quality.

Use good cutting fluid and don't forget the little quarter turn back dance...! :)


added: they call those Irwin Hanson. Maybe Irwin is just the distributor?
 
Last edited:
I threw my HF set in the trash. Like John said, NO quality control at all.
I have them too. When I need one I go buy an Hanson and throw out the HF and put the Hanson in its place. So I paid $10 for the metal box:lol:

Truly, I discovered how bad they were when I was using a die that actually stretched over the metal rod instead of cut into it. POS!
 

Users who are viewing this thread

Back
Top Bottom