Builds Project "Devil Frog" - Isaac's '69 FJ40

[cruisermatt]

You need a programable ECU for any injectors other than the OEM speced

But do they fit in the factory location or do you need the supra fuel rail as well?

And thanks for reciting the first rule of AFR, I almost forgot that in the twenty times a day someone spits that out on the Internet.

 

[Devil Frog]

They fit in place perfectly in the 3FE, even plug into the harness, and have matched impedance

But do they fit in the factory location or do you need the supra fuel rail as well?

And thanks for reciting the first rule of AFR, I almost forgot that in the twenty times a day someone spits that out on the Internet.

 

[alia176]

looking good but you gotta work on your video and photographing skillz

 

[Devil Frog]

The body is coming back this week, so I got the fuel tank plumbing and electrical done while I still have access.

 

[alia176]

The wires are getting labeled, correct?

 

[Devil Frog]

The wires are getting labeled, correct?

They will be labeled on the other end. I would love to get a hold of one of those digital label printers.

I am using a FJ62 main harness/fuse/relay boxes because I am using a the 3FE engine harness and the FJ62 steering column. I also have to splice in 9 auto meter gauges,York Compressor clutch & OBA control switch, and the diff lock LED.

Very good point on wire labeling, that is the difference between minimal frustration and pulling your own teeth out.

I also have a roll over valve that I will plumb that fuel tank vent line.

 

[alia176]

They will be labeled on the other end. I would love to get a hold of one of those digital label printers.

I am using a FJ62 main harness/fuse/relay boxes because I am using a the 3FE engine harness and the FJ62 steering column. I also have to splice in 9 auto meter gauges,York Compressor clutch & OBA control switch, and the diff lock LED.

Very good point on wire labeling, that is the difference between minimal frustration and pulling your own teeth out.

I also have a roll over valve that I will plumb that fuel tank vent line.

Go over to Summit electric and pick up one of them wire labeler where you can write in your own info using a sharp tip Sharpie. Here's mine: http://www.cableorganizer.com/3m-write-on/ Who knows, Home Depot/Lowes might carry them too.

 

[DanS HJ-45]

Go over to Summit electric and pick up one of them wire labeler where you can write in your own info using a sharp tip Sharpie. Here's mine: http://www.cableorganizer.com/3m-write-on/ Who knows, Home Depot/Lowes might carry them too.

I need to buy one of these....

http://www.buyheatshrink.com/dymo-l...blryDwn6QfMJjrA6libV8pN7rvlEYUyCzjxoC3Pnw_wcB

Way sexy....

Dan

 

[Devil Frog]

 

[jstncse]

I like it

 

[BionicCruiser]

is that airbrushed? looks cool.

 

[Devil Frog]

is that airbrushed? looks cool.

Yup airbrushed. I ended up taking it to an old buddy from high school for a paint/body. He typically does low riders and hot rods and really wanted to do mural. The design is a USMC Recon Jack, a nod to my time in the reserves.

 

[Devil Frog]

This is my main gauge panel:

I have 4 more that I need to find space for: fuel, amp, volt, and air pressure.

 

[Devil Frog]

Bumper installed

Modifying dash for FJ62 Column

 

[Devil Frog]

Got the winch cleaned up, oil changed, some Synthetic line, and new wiring:

 

[Devil Frog]

T-case parking brake

 

[alia176]

SCHWIIIIIIIIIING !!!!! Close up of that parking brake setup please and various angles.

 

[Devil Frog]

SCHWIIIIIIIIIING !!!!! Close up of that parking brake setup please and various angles.

 

[Devil Frog]

The tub is back on the frame.

 

[Pyro-boy]

Looking good! I still have that extra winch controller if you still need one.

Vince