Official ONSC member buying/selling thread (38 Viewers)

[Malleus]

I'm not following the "studs" reference. The rear full float axle locknut has three holes in its face, that's what the pins are for. There isn't room (in mine) to get a wrench around the nut. The only choice is the pin wrench or a chisel.

Maybe I'm missing something obvious.

 

[JohnVee]

I'm not following the "studs" reference. The rear full float axle locknut has three holes in its face, that's what the pins are for. There isn't room (in mine) to get a wrench around the nut. The only choice is the pin wrench or a chisel.

Maybe I'm missing something obvious.

My memory is cloudy about what my locknut looks like, and I can't recall my 94's build date, but the tool in Stan's pic is the one I used.

 

[Malleus]

This is what the full float rad locknut looks like

 

[Malleus]

This is the full parts diagram

 

[JohnVee]

The three slots in the tool encase those round pins.

 

[Malleus]

The locknut screws are there to align the nut and thrust washer (it's keyed). Having bent that thrust washer, I wouldn't lean on it, or anything connected to it; it's very soft.

 

[Malleus]

I missed the cancellation of the third tool order by a day. They now claim it's in the mail. We'll see.

Thanks for the offer anyway!

 

[forrest5000]

Have a set of factory floor mats for a 80 series , in gray. They are near mint. Thinking $45

 

[fj40z]

Have a set of factory floor mats for a 80 series , in gray. They are near mint. Thinking $45

Eric I’ll grab those from you

 

[forrest5000]

Eric I’ll grab those from you

They are yours.

 

[uzj100]

Anyone selling a 60 or 62 at non BAT prices? A friend is looking.

 

[Hokie LX]

Anyone selling a 60 or 62 at non BAT prices? A friend is looking.

You’re referring to me, right? Lol

I’m also looking

 

[roadstr6]

Anybody got a metal carport they want to sell? Looking for something around 12x24. 10x20 will do in a pinch. Does not have to be nice, or even complete. I will disassemble and re-assemble at my location. I bought an old boat and it needs hard cover. New prices for these stupid, ugly little metal carports are complete insanity and 10+ weeks out for installation. I may have to just build a little pole barn myself. I know it would be cheaper than buying a flimsy new metal one for sure.

 

[S4Cruiser]

Anybody got a metal carport they want to sell? Looking for something around 12x24. 10x20 will do in a pinch. Does not have to be nice, or even complete. I will disassemble and re-assemble at my location. I bought an old boat and it needs hard cover. New prices for these stupid, ugly little metal carports are complete insanity and 10+ weeks out for installation. I may have to just build a little pole barn myself. I know it would be cheaper than buying a flimsy new metal one for sure.

10 Ft. x 20 Ft. Portable Car Canopy

Amazing deals on this 10Ft X 20Ft Portable Car Canopy at Harbor Freight. Quality tools & low prices.

www.harborfreight.com

Not a permanent solution but I’ve been pleased with the quality of the one I bought. Mainly to keep the sun from beating down on my while I redo the boat. Been up since may and no issues yet.

 

[JohnVee]

Looking for a small-medium duty gas pressure washer for cleaning the house, dock, and steel garage.

I’d go electric except for the little bit that it’ll be used 150’ away from a power source.

 

[Malleus]

Looking for a small-medium duty gas pressure washer for cleaning the house, dock, and steel garage.

I’d go electric except for the little bit that it’ll be used 150’ away from a power source.

New or used? I don't have a used one for you, but the Ryobi 3000psi I bought 3 years ago has been stellar (primarily due to the Honda engine and the fact the that the only Ryobi part on it is the label).

 

[Comet]

Borrow or buy?

Looking for a small-medium duty gas pressure washer for cleaning the house, dock, and steel garage.

I’d go electric except for the little bit that it’ll be used 150’ away from a power source.

 

[JohnVee]

Borrow or buy?

Buy.

 

[angerhater]

Looking for a small-medium duty gas pressure washer for cleaning the house, dock, and steel garage.

I’d go electric except for the little bit that it’ll be used 150’ away from a power source.

john, I have one in my shed that got molested by my son in law if you want to tinker with it.. FREE... it was Al's

 

[JohnVee]

@angerhater Ill be in touch.