Official ONSC member buying/selling thread

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

I'm not following the "studs" reference. The rear full float axle locknut has three holes in its face, that's what the pins are for. There isn't room (in mine) to get a wrench around the nut. The only choice is the pin wrench or a chisel.

Maybe I'm missing something obvious.
 
Malleus said:
I'm not following the "studs" reference. The rear full float axle locknut has three holes in its face, that's what the pins are for. There isn't room (in mine) to get a wrench around the nut. The only choice is the pin wrench or a chisel.

Maybe I'm missing something obvious.
Click to expand...
My memory is cloudy about what my locknut looks like, and I can't recall my 94's build date, but the tool in Stan's pic is the one I used.
 
This is what the full float rad locknut looks like

20210612_081316[1].webp
 
This is the full parts diagram
1630524922323.webp
 
The locknut screws are there to align the nut and thrust washer (it's keyed). Having bent that thrust washer, I wouldn't lean on it, or anything connected to it; it's very soft.
 
I missed the cancellation of the third tool order by a day. They now claim it's in the mail. We'll see.

Thanks for the offer anyway!
 
Have a set of factory floor mats for a 80 series , in gray. They are near mint. Thinking $45
 
Anybody got a metal carport they want to sell? Looking for something around 12x24. 10x20 will do in a pinch. Does not have to be nice, or even complete. I will disassemble and re-assemble at my location. I bought an old boat and it needs hard cover. New prices for these stupid, ugly little metal carports are complete insanity and 10+ weeks out for installation. I may have to just build a little pole barn myself. I know it would be cheaper than buying a flimsy new metal one for sure.
 
roadstr6 said:
Anybody got a metal carport they want to sell? Looking for something around 12x24. 10x20 will do in a pinch. Does not have to be nice, or even complete. I will disassemble and re-assemble at my location. I bought an old boat and it needs hard cover. New prices for these stupid, ugly little metal carports are complete insanity and 10+ weeks out for installation. I may have to just build a little pole barn myself. I know it would be cheaper than buying a flimsy new metal one for sure.
Click to expand...

www.harborfreight.com

10 Ft. x 20 Ft. Portable Car Canopy

Amazing deals on this 10Ft X 20Ft Portable Car Canopy at Harbor Freight. Quality tools & low prices.
www.harborfreight.com www.harborfreight.com

Not a permanent solution but I’ve been pleased with the quality of the one I bought. Mainly to keep the sun from beating down on my while I redo the boat. Been up since may and no issues yet.
 
JohnVee said:
Looking for a small-medium duty gas pressure washer for cleaning the house, dock, and steel garage.

I’d go electric except for the little bit that it’ll be used 150’ away from a power source.
Click to expand...
New or used? I don't have a used one for you, but the Ryobi 3000psi I bought 3 years ago has been stellar (primarily due to the Honda engine and the fact the that the only Ryobi part on it is the label).
 
Borrow or buy?


JohnVee said:
Looking for a small-medium duty gas pressure washer for cleaning the house, dock, and steel garage.

I’d go electric except for the little bit that it’ll be used 150’ away from a power source.
Click to expand...
 
JohnVee said:
Looking for a small-medium duty gas pressure washer for cleaning the house, dock, and steel garage.

I’d go electric except for the little bit that it’ll be used 150’ away from a power source.
Click to expand...
john, I have one in my shed that got molested by my son in law if you want to tinker with it.. FREE... it was Al's
 
You must log in or register to reply here.

Share this page

Back
Top Bottom