Local For Sale/Wanted Section! (3 Viewers)

[77landsitter]

76 and 78 FJ40 Parts

I have to make some room in the garage for the new to me cruiser I just picked up so I have some stuff for sale.

78' cowl no rust -250
78' hood good slight pitting sanded down ready for primer -100
78' front bib good shape -50
78' front fenders so so with marker lights -50
76' front and rear axles- 350
78' steering column and wheel -50
lots of other stuff just ask i may have it.

Thanks
Dan
610 360 9549

 

[zucruisers]

i have some toyota 8" diff parts, changed the gears/lockers in the buggy...now i need to sell these to make some of that $ back

4.10 4 cyl R&P gearset, with pinion bearings/races included - $40

4.10 V6 R&P gearset - $40

2 sets of 4.88 4cyl gears, installed in a diff with an open carrier - $250

RD 132 ARB air locker, with 4cyl bearings - $650, or installed in one of the 4.88 diffs for $850

V6 4-pin lockright, in a V6 carrier, with brand new timken conversion bearings to fit in a 4cyl diff - $300, or installed in one of the 4.88 diffs for $500

everything is located in northumberland, pa 17857, i can ship it or it can be picked up here, in schuylkill haven, pa, or at rausch creek offroad park

 

[kb3gun]

Need a set of rear 55 springs for my SOA 40.
Western PA/MD/Eastern OH I can pick up.

Located in Somerset PA 15501 for shipping.


Thanks! -Bill

 

[norville]

FS 6.5 western power angle plow setup

Folks, I have a decent 6.5' plow that was set up for an early bronco. It has like new springs and the lines look newer. One side cylinder is very good and holds well, one may need to be rebuilt or it was just out of fluid. It's fairly solid no rot, but it will need a cutting edge. Western hydro electric pump with in cab controls.

I'm in Pa 18707, pickup only, it is heavy, I may be able to deliver locally for a few $$

$250 for the blade, frame, pump and controls everything I have.



Trade for a ford 2.8 (bronco ii/ranger) or an early ford 2.0 pinto engine..

bob

 

[blackandbluefj]

looking for a spare tire to match my 39.5" iroks either another irok or something close anyone got something they wanna get rid of . let me know pm is probably best


thanks

Bryon

 

[mls57jax]

Rim needed

I need one black steel 15X8, ten spoke rim, 6 on 5.5 with 3.5" backspacing (Type 51 style?). Doesn't have to be pretty but must have a good bead seating surface. I'll be using it as a spare.

Mike in PA

 

[zucruisers]

looking for a spare tire to match my 39.5" iroks either another irok or something close anyone got something they wanna get rid of . let me know pm is probably best


thanks

Bryon

i know of someone with a 39.5"x13.5x17 irok, almost full tread with some rock rash, currently on a cragar soft 8 steel wheel, 8 lug...pm me if you're interested

 

[woytovich]

New Warn Series 12 hydraulic winch for sale

New Warn Series 12 hydraulic winch for sale

Trying to sell this "locally" to avoid shipping: pain for me, cost for buyer...

https://forum.ih8mud.com/sale-parts/305210-new-warn-series-12-hydraulic-winch-ny.html

Mark

 

[racefanmartin]

(4)-315/75/16 Goodyear MTR's

I have four Goodyear MTR's 315/75/16 = 35's on Wheelers steel wheels.

The wheels are 16x8 and I will include the black lug nuts to go with them.
They have about a third tread left...If you would like more info please PM me.
I would like to see $300.00 for everything.
Thanks,

Matt

Price reduced...$200.00 these need to go...


SOLD.....

 

[caz]

Old Victorian Bulldog Puppies!

We had a litter of puppies last week. If anyone is interested, see here -
lovablebulldog.com

They are a more athletic breed of bulldog than an English - fewer health problems, more practical.

Andy

 

[truvaine]

P.S. I am a Mac user and am unable to upload pic's...If you are interested
PM me with your e-mail and I'll send you the Pic's.

you should be able to upload pics; i'm on a Mac and dont have too much trouble..
if you want, email the pics to me and i can host them & post

PS - i see you driving around Etown all the time. i wave, although i'm in my black TDI golf (usually with a bike or kayak on the roof). i guess if i were driving my toyota, you might notice haha

 

[truvaine]

I have four Goodyear MTR's 315/75/16 = 35's on Wheelers steel wheels.

The wheels are 16x8 and I will include the black lug nuts to go with them.
They have about a third tread left...If you would like more info please PM me.
I would like to see $300.00 for everything.
Thanks,

Matt

P.S. I am a Mac user and am unable to upload pic's...If you are interested
PM me with your e-mail and I'll send you the Pic's.

pictures:

 

[racefanmartin]

Thanks for posting the pic's....see ya around town

 

[jamarquardt22]

Taco doors?

Im looking to make some half doors for my taco this winter. anyone know where I can find some cheap? 95.5-04

 

[ruger280]

The easy pull in New Rinngold gets about $25 per door. Not a bad price.

 

[egil1963]

damn shame you're in PA, I could use those in NV.

 

[V8FJ4078]

Anyone have a early SM465 from a 4X4 Chevy? Must have 10 spline output shaft.

Anyone cleaning out their garage? Tired of stubbing your toe on it as you walk by it all the time?

 

[jamarquardt22]

The easy pull in New Rinngold gets about $25 per door. Not a bad price.

Where is that I tryed to mapquest that and couldnt find a location. Got a phone number too?

 

[kb3gun]

He made a typo. It's New Ringgold.
Joe's Used Auto Parts
aka "Ez Pull & Save Auto Parts"

 

[zucruisers]

Anyone have a early SM465 from a 4X4 Chevy? Must have 10 spline output shaft.

Anyone cleaning out their garage? Tired of stubbing your toe on it as you walk by it all the time?

pm jeff, i gave one of them to him awhile back, i know it was a 4x4 sm465, not sure if it was 10 spline or not, but he might still have it