Trollhole said:
I knew when you hit 41 you'd get loopy
It does Exist (1 Viewer)
- Thread starter ClemsonCruiser
- Start date
This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.
I knew when you hit 41 you'd get loopy
What these doubters don't recall is I have driven 3 wheeled cruisers, I have driven windshieldless cruisers, I have driven topless cruisers through a raging sleet storm, I have driven cruisers with no rear brakes, I have driven cruisers with no wires running to the alternator, I have driven cruisers upside down, I have drive cruisers with front wheel drive only, I have driven cruisers with no shocks!!!!!
You fools forget I can do more with a 1/3 of a cruiser than most can do with a whole reliable cruiser
You forgot driving with only 3 wheels while the fourth one passed you.
And I will never forget driving with no windshield, that was probably the coldest I have ever been in my life.
Are you ok Troll,, sure your not like throwing up, or having a really bad fever. Maybe you should check yourself into the er and I mean right now this could be fatal.
ClemsonCruiser
Supporting Vendor
- Thread starter
- #224
Well I now think I have more hours into the trans tunnel than the actual engine swap 
but I am finally done with it well except for final welding, sanding, paint, sound proofing , etc. 
It is very rectilinear in appearance which contrasts nicely to the more subtle lines on the 45
but I am finally done with it well except for final welding, sanding, paint, sound proofing , etc. It is very rectilinear in appearance which contrasts nicely to the more subtle lines on the 45
ClemsonCruiser
Supporting Vendor
- Thread starter
- #226
thanks Doc, I really wish I had the proper fab. tool to produce some smooth lines, but with only an angle grinder and a cheap lowes welder my endeavors are limited I know to you guys it has to look so simple but it is amazing how much time it has taken, so many clearance issues, it is much more complicated than it appears.....but like Marshall said it aint got to be pretty just functional
On v.2.0, radius all your corners and hammer them down to meet in the middle. Then cap them with a circular piece that has been cupped. Weld and grind to desired finish. I know you didn't have time this go around, but just tossing ideas out there for the re-rebuild after R.A.T..
ClemsonCruiser
Supporting Vendor
- Thread starter
- #228
Compared to the old days in Clemson when he would have left the cardboard templet in there for a month and then used 3 different sizes of metal this thing is great, good fabbing Virgo.
ClemsonCruiser
Supporting Vendor
- Thread starter
- #230
Are you going to paint a helicopter landing pad on that thing...that thing is so big you could land a Huey on there....and why don't you weld on two cup holders so when your sweetin your nuts off out west you'll have somewhere to put your frosty beverage
ClemsonCruiser
Supporting Vendor
- Thread starter
- #232
CruisinTiger said:
Lol it has to be that big to clear the H55 and split case.... They dwarf the original 3spd
Also got the cup holder covered!!
but like Marshall said it aint got to be pretty just functional [/QUOTE]
Quite so, and as I said good work I do so hope I don't have to see you and Marshall on the mini together it would be tooooo funny for words. now stop typing and continue welding and wrench turning time's a wasting.
[/QUOTE]Quite so, and as I said good work I do so hope I don't have to see you and Marshall on the mini together it would be tooooo funny for words. now stop typing and continue welding and wrench turning time's a wasting.
Are you kidding it took me three days just to make one bracket 4 inches in length on my build. You are under the gun on time and that is as I said a real nice box. You just keep burning up the build and you'll make the deadline we have faith in you. (Wait a minute did I just say that,.... well maybe nobody will notice) LMAO
at the end, don;t do as I sometimes do then just doesn't work as well. 
ClemsonCruiser
Supporting Vendor
- Thread starter
- #236
oh man.... ouch ouch, that stings LOL great stuff!!
ClemsonCruiser
Supporting Vendor
- Thread starter
- #237
Are you kidding it took me three days just to make one bracket 4 inches in length on my build. You are under the gun on time and that is as I said a real nice box. You just keep burning up the build and you'll make the deadline we have faith in you. (Wait a minute did I just say that,.... well maybe nobody will notice) LMAO
thanks for the kind words Doc, I like the pressure it makes my ADD brain focus a little better
Looks very modern. I think you ought to put some glass in it and paint it red.
not a fan of the rectilinear appearance, eigh Rick
I'm just looking out for your's and Marshall's toes.
Southeast Overland
Get lost! Go explore!
I'm just looking out for your's and Marshall's toes.
Marshall wears shoes. JP does not. One will be fine - the other... well we will see!