CLCC Tech Day thread (7 Viewers)

[Von Hayek]

It looks like I just threw a rod in the 62. I haven’t been to a tech day in a while—do you think this is something that we can get done?

 

[Jakes40]

It looks like I just threw a rod in the 62. I haven’t been to a tech day in a while—do you think this is something that we can get done?

That sucks!

No I don’t think replacing rod bearing on an LS is a Tech Day think.

 

[Von Hayek]

That sucks!

No I don’t think replacing rod bearing on an LS is a Tech Day think.

You sure? I think this is something you could do. Just tell me what tools to hand you.

 

[StaleAle]

If my ASFIR skids get in before that, I'd like to use a slot to get them and the MT Sliders installed in time for Fall Crawl!!

Skids and sliders do not usually warrant using a lift unless there is welding involved so I'd bring some cardboard or yoga matts to lay on if I was planning those tasks. Projects that would have priority for a lift generally involve more than one tire coming off the vehicle simultaneously, or exhaust and driveline work.

 

[unleashd]

Skids and sliders do not usually warrant using a lift unless there is welding involved so I'd bring some cardboard or yoga matts to lay on if I was planning those tasks. Projects that would have priority for a lift generally involve more than one tire coming off the vehicle simultaneously, or exhaust and driveline work.

Point noted

 

[b4wheeler]

I'm Back!! This time in a Tacoma........

 

[afgman786]

I'm Back!! This time in a Tacoma........

Good to see you back on here! Still rocking the Camaro?

 

[rrc swb]

When's the next one?

 

[Jakes40]

No tech day is scheduled at this time.

 

[rrc swb]

No tech day is scheduled at this time.

One could hope. LOL

 

[D21FJ60]

One could hope. LOL

Do you have a garage? We could over run your neighborhood

 

[BullRunOverland]

When's the next one?

As long as no one needs a lift...I could squeeze one in in January. But December is booked up!!

 

[CondeCruiser]

I could host one. I just have to get my 40 rolling again so we could use the lift. Axles should be done this weekend. Maybe January?

 

[rrc swb]

Do you have a garage? We could over run your neighborhood

I don't. That's my biggest issue.

I wanted build a detached garage, but one of the club members (I forgot his alias) that works with this type of construction mentioned that due to easement it's not feasible.

 

[rrc swb]

As long as no one needs a lift...I could squeeze one in in January. But December is booked up!!

I could host one. I just have to get my 40 rolling again so we could use the lift. Axles should be done this weekend. Maybe January?

I'll host the pizzas like last time at OTRAMM.

 

[Svensk120]

going to need to do a timing belt on the gx470....

 

[CondeCruiser]

I guess we need to figure out a day to put on the schedule.

 

[Jakes40]

@Svensk120 i have never done a timing belt on a gx470 but it may be a bit ambitious for a tech day.

 

[Svensk120]

@Svensk120 i have never done a timing belt on a gx470 but it may be a bit ambitious for a tech day.

Stump was thinking it wouldn't be that hard as it is the basic 2UZFE 4.7 engine like a tundra...

I have looked up a walk through on Youtube and it seems to be pretty straight forward but still over my skill level alone.

part 1 taking everything apart



part 2 putting it back together

 

[CondeCruiser]

Well if we have tech day at my place and you have to leave it overnight, I will part it out.