Brake line/hose/T-fitting part# ??'s

[jsuthey]

Hi All,just had a couple quick questions on part #'s for a 69 40.I need the frame to rear axle rubber brake line in 10mm and the T-fitting on the rear axle in 10mm also.Also need 1 more T-fitting for the front brake lines.

I looked on SOR and they had alot of the parts I am looking for,just want the best deal and to get the right parts!!

I am working on finishing my rear disc brake conversion.Just going to change over to 10mm.I have been following Rigger's thread and it has been lots of help.

Thanks,John

 

[paranoid56]

lol funny you are looking for these. i also cant seem to find any and heading to the junk yard in the next 20 min to go find some off a mini truck.

 

[hughjazz]

Hi All,just had a couple quick questions on part #'s for a 69 40.I need the frame to rear axle rubber brake line in 10mm and the T-fitting on the rear axle in 10mm also.Also need 1 more T-fitting for the front brake lines.

I looked on SOR and they had alot of the parts I am looking for,just want the best deal and to get the right parts!!

I am working on finishing my rear disc brake conversion.Just going to change over to 10mm.I have been following Rigger's thread and it has been lots of help.

Thanks,John

I went to napa, and asked for the parts off of a '2000 tundra. IIRC.
P/n
381328 It's like 20" long, so it may be better for a lift kit in the future. There is a picture on the napa site, you can verify if that is the right ends.

 

[paranoid56]

I went to napa, and asked for the parts off of a '2000 tundra. IIRC.
P/n
381328 It's like 20" long, so it may be better for a lift kit in the future. There is a picture on the napa site, you can verify if that is the right ends.

and they had the Tee in stock? as i was just there and they couldnt find s*** LOL

 

[hughjazz]

and they had the Tee in stock? as i was just there and they couldnt find **** LOL

no, didn't have the hose either.

 

[bsevans]

The 3-Way Tube Tee with Mounting Hole I use is a BrakeQuip.

M10 Tee

 

[paranoid56]

hey OP, if you want i picked up an extra axle T fitting from a mini truck you can have ffor 10 bucks (what it cost me) and shipping. felt kind wird buying 9 sets of those and totalling almost 100bucks lol. but i needed a few, also picked up some right angle fittings too, but didnt get any rubber hoses. you might just pick up a metric adapter and some 3an stainless lines

 

[jsuthey]

Thanks for the replys/info.
bsevans-I have seen that photo before,looks like a good setup.I will look into the BrakeQuip Tee.

It seems like it should be pretty easy to get something not OEM for the rubber line.I am going to pick up a few more fittings/lines at Napa tomorrow,so I will see what they can do.

John

 

[jsuthey]

Went by Napa today,no 3-way T-fittings.They had lots of rubber lines,but in order to get the right one I need the T-fitting/3-way.Forgot to ask about the 2000 Tundra hose.I am still looking into the BrakeQuip set-up.

Hey bsevans,what SS line do you have for the frame to axle/T-fitting,Part # on that website??.I also could not see any prices.

Thanks,John

 

[bsevans]

Went by Napa today,no 3-way T-fittings.They had lots of rubber lines,but in order to get the right one I need the T-fitting/3-way.Forgot to ask about the 2000 Tundra hose.I am still looking into the BrakeQuip set-up.

Hey bsevans,what SS line do you have for the frame to axle/T-fitting,Part # on that website??.I also could not see any prices.

Thanks,John

You can order the BrakeQuip Tee from any of their distributors. I know the dealer here in Tucson not only sells their products, but will make custom lines and send them to customers in the US and abroad.

Magill's

If you go to their dearler map you will find a dealer in San Jose, Gilroy, Watsonville and Salinas.

Dealer Maps

 

[jsuthey]

Wow,Thanks!! The dealer in Gilroy is just down the street from the school we are building/framing.

 

[jsuthey]

Hey paranoid65,do you still have an extra 3-way? If so I will take it.I will PM ya'.I would like to see a pic.if you got one.

Went to the brake shop in Gilroy and they made me a custom rubber hose and I got the 3-way T-fitting that goes with it there also.So they just drilled out the mounting hole a little bigger for the T-fit. to mount on the axle w/ the breather bolt.Fits great and do not charge to drill it out.Parts were a deal too.

Still looking for a 3-way for the front off the MC to the front discs. I need a 3-way there that I can bolt to the frame right by the D/S caliper connection.I had one there w/a mounting tab,but it's 9mm.

Any ideas on what to use,the guy at that shop did not have any.Napa did not either.P/N's,$SOR,ect..??

Thanks,John

 

[Dusty 66]

1969 should be 9mm

9mm Stuff
https://forum.ih8mud.com/40-55-series-tech/117559-69-older-9mm-brake-line-adaptors-faq.html

More 9mm

 

[paranoid56]

not sure if your MC is the same as mine but i have an also extra bracke with a Tee on it that mounts to the MC.

 

[paranoid56]

heres teh MT tee fitting i was talking about. works perfect for me.

 

[jsuthey]

Hey thanks for the pic,I could use one of those fittings in the front also.

Do you still have any extras?

I also still need some tombstone mount tabs for the rear.I have a welder lined up.Anyone have any?

Thanks,John

 

[2fpower]

Old thread. Anyone have a solution to this in Toyota parts?