I might go with a filter like that on my OM617 project. It's considerably smaller than the Mann Provent.
Builds Big Red Toy
- Thread starter The Phoenician
- Start date
This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.
- Thread starter
- #1,522
Might do the same, too broke right now and Aurora is in between jobs. Thanks for posting it Boots. When you get a chance snap a few pics that show where you located it.
After fixing my rear pinion leak, the vent is now my only oil leak (that leaves spots on the ground). Time to go to harbor freight!
- Thread starter
- #1,524
Document it well so amateurs like myself can only mess it up once.
- Thread starter
- #1,525
Tried to pull a Johnny C on my way back from the gym this evening. Got it to a mere 20 PSI ( nowhere near his 35psi), but I could hear the scream of the turbo over the radio. I probably won't be doing that again for a while.
Have a good Veteran's Day, Mike
- Thread starter
- #1,527
Thanks P. Yesterday was the marine corps birthday, today is veterans day, I think I'll just keep drinking for the rest of the week. Cheers guys
Happy Veterans Day, Mike.
- Thread starter
- #1,529
Thanks Dave. I finally got a day off and it's too cold to do anything outside. So drinking it is
Cold? Come on. Layer up and get some wrenching done.
- Thread starter
- #1,531
my mind is willing, my knuckles, and knees are not. Maybe in another shot or two I'll be warm enough
.
X2 on the Happy Veterans Day Mike. Thanks for your service.
- Thread starter
- #1,533
Luis thanks.
- Thread starter
- #1,534
Had trouble cranking the engine today on my way to the gym. Never had that issue before so I thought it was the cold weather. Turns out the fuel return line is leaking pretty badly. It was too dark and cold to fix. So I will most likely get to it after my drill weekend. That's too bad because I wanted to drive it to gauge my MPG with the new sexy bumper on.
I also tried to take a picture, but managed to get soaked in diesel instead
. I think I'll have a shot of Tito's handmade vodka and call it a night.
I also tried to take a picture, but managed to get soaked in diesel instead
. I think I'll have a shot of Tito's handmade vodka and call it a night.
I drove 99% highway up through the mountains of Tennessee at 75mph+ last weekend averaging 12.7mpg with my 37s and my sexy new bumper. Not too shabby, eh? Try and beat that with your boss 4bt... Yeah I know... Shouldn't be too difficult LOLOL!!!
...via IH8MUD app
...via IH8MUD app
- Thread starter
- #1,536
That's pretty good P. I think I was getting between 9 and 11 on the 3fe. Right now the rig is down until I can get to it, which probably won't be until early next week. What gearing do you have, is it 4.11 or 4.88?
Yeah I was actually really surprised. I could hardly believe I got more than 200 miles before I hit a quarter tank haha. I've got 4.88s. Sort of feels the same as when I had 33s and 4.11s.. or at least the speedo is off by about that much. Aidan got just over 16mpg on the same trip in his 80 :O (1FZ, 35s and 4.11s). I look forward to when you report back on your findings.
...via IH8MUD app
...via IH8MUD app
- Thread starter
- #1,538
My free name plates came in. Have to figure out a good place for em.
- Thread starter
- #1,539
213000 miles later and still trucking
Last edited:
bluehawk
Appalachia Cruisers
Got my snokel in today. Love how they send no instructions with this thing. Don't recall if my template has the fourth hole in it or not. Ill check and see tomorrow. It has the three holes that mount it to the fender like the ones in your picture. I'll check and then get back with you.
