kWould you mind explaining it a little bit? Was thinking it's direct fit...
Follow along with the video below to see how to install our site as a web app on your home screen.
Note: This feature may not be available in some browsers.
This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.
kWould you mind explaining it a little bit? Was thinking it's direct fit...
Same question here.What method are you using to flatten the front dust caps?
Are these the 20s? If so what tire size??
It looks like you are not even clearing the front hub. I think thts your problem. The stock lugs should work. You need some 1.25” wheelI just received a set of 18" TRD wheels- stock lugs won’t fit- I’m assuming that the tundra lugs are what I need?View attachment 1921412
Is this how your hub looked with the rim installed? What lugs did you use? My stock LC lugs are tThey will fit but you will need to flatten the front dust caps. I flatten mine and used a dremel sander to sand away a little of the inside of the center cap until it was able to pop into place.View attachment 1900687
They will fit but you will need to flatten the front dust caps. I flatten mine and used a dremel sander to sand away a little of the inside of the center cap until it was able to pop into place.View attachment 1900687
They will fit but you will need to flatten the front dust caps. I flatten mine and used a dremel sander to sand away a little of the inside of the center cap until it was able to pop into place.View attachment 1900687
It IS around the hub - check the pic. The outer center of the rim curves in over the hub a bit, but there is space between the front of the hub bolts and the rim, it’s sitting flush against the mating surface. I don’t have fitment issues with the rim, it’s just the lug nuts.Should be around the hub. Not against it. Like the stock wheels in this picture.
View attachment 1921464
There are tons of people who run the Tundra rims from the last few model years- they all have the same hub bore (110mm) and bolt pattern (5x150mm). I haven't been able to find anyone else with these exact rims, but I can't be the only one???...I've ordered a set of 2018 Tundra lug nuts, I'll post when they arrive.Interesting. You are probably one of the first guys to run these new BBS TRD wheels on a 100 series. I googled the wheels and the style seems the same; Maybe they are smaller? You should probably start a new thread and document your solution if this is going to be an issue.
View attachment 1921475
Going to be running a similar setup but with KO2’s, was leaning towards 285/70/17 because I’m not sure if the 75’s will rub at all. Can you shed some light on this for me?
17" TRD Rock Warriors with 1-1.25" spacers (not positive, came with the wheels) and 285/75/17 Cooper St Maxx (34")
I think this tire size looks fricken perfect. A little meatier than the 33s everyone runs without the work required to fit 35s properly. I'll test out rubbing under compression this weekend.
There are tons of people who run the Tundra rims from the last few model years- they all have the same hub bore (110mm) and bolt pattern (5x150mm). I haven't been able to find anyone else with these exact rims, but I can't be the only one???...I've ordered a set of 2018 Tundra lug nuts, I'll post when they arrive.
Looks nice! Just spacers for the front correct? Did you have any rubbing? Trying to see how large I can go without any rubbing. Also, what kind of tires you running?Just got my 2017 Rock Warriors mounted up with Spidertrax 1.25" spacers running 295/70/17's.View attachment 1921501
Thanks, I really like the wider stance. I went ahead and trimmed the inner fender liner while I had the wheels off (just the part that sticks out towards the tire) I then sprayed the exposed metal with a rubberized coating. So far I haven't heard any rubbing at all in forward or reverse. I installed spacers on the front and rear. As for the tires, I have Nitto Terra Grappler G2's.Looks nice! Just spacers for the front correct? Did you have any rubbing? Trying to see how large I can go without any rubbing. Also, what kind of tires you running?
Going to be running a similar setup but with KO2’s, was leaning towards 285/70/17 because I’m not sure if the 75’s will rub at all. Can you shed some light on this for me?
I found them on Ebay- $899 shipped for 4. I overnighted a set of splined lug nuts, hoping they work, I'll post an update.I’m pretty active here on MUD and a 100 series FB page. You are probably not the first, just the first to document it. I haven’t seen anyone with these. Probably because they are so new, they aren’t a very affordable option for guys with Older Rigs like us. How did you come accross that set? How much?