The wiper seals on my birdfields is starting to go, one side worse than the other. Forming nice little grease patties on my driveway. 1990 LN106 series hilux. I have the same factory axle as an '85 pickup, manual hubs etc.
I am going to rebuild the birdfields this summer. However, right now it...
Hello all,
After going through hell and back to get the proper head for my 3B, I'm now installing all the valves and springs etc. I also ordered a pack of new valve stem seals to install as well, and I'm having a terrible time pressing them on. Unfortunately no where local do they have a...
Any experience with this procedure. Have engine out and will do clutch TOB, PP etc. How complex is the rear main seal replacement? Can it be done one piece from the outside.
Does this mean the seal between the transmission and transfer case has finally given up? This is after sitting for a couple of weeks. Last night I noticed the fluid about an inch in the tube at the bottom. Now it’s definitely higher.
Well I've done this twice now. The first time, I used a pvc pipe that supposedly got the right depth. The second time, I used the wits end tool. Since I have failed twice, I'm looking for tips or confirmation on my checklist before I try this again.
1. Use wits end tool to get flush mount
2. Be...
The other day, when I went to replace my rear brake pads, I found oil *everywhere* under the back of the truck. Complete mess. Seems to be the pinion seal. I dumped a quart of gear oil into the diff and it didn't fill it. I just got back from about a 3000 mile road trip in the truck. No...
Hey all - so I’m prepping to possibly have to replace my rear main if I can pinpoint that’s the source of my leak. In looking up the seal part numbers I get the following.
90311-99065
90311-99001
Where the 99001 is listed for 84-87 FJ60. I have an 888000 serial number motor so I think I’m in...
When fitting the driver's side axle seal, it went a bit too far, about 1.5mm. It is not flush with the inner lip. Does anyone think this will be an issue and leak?
Another try at installing my windshield today ended in frustration. This time using a Toyota seal, if you remember my earlier post the brand x seal was rock hard and I couldn't even get it to stay on the glass. Try number two took me over an hour but using duct tape as I went I got the seal on...
Hi there! I was quoted $800+ by a shop to fix this rear axle seal leak, I’m new to cruisers and bought my LX 3 months ago and am baselining all maintaince items slowly so I apologize for any ignorance. Is the condition of this severe and urgently needing replacement? Let me know if more pictures...
Looking at purchasing the Birfield Seal/Knuckle Rebuild kit form Cruiser Corp. Is it a good kit and will it have everything i need? It says wheel bearings not included. Anyone know a part number for the wheel bearings? TIA!
Description is in the title. 93 FZJ80, with a leaking dizzy (comes out the hole in the bottom of the cap).
How long can I drive with this leak? Will it affect any other parts, other than the distributor? Shop quoted me about 1k for replacement and install??? WTF? I really would not like to...
Anybody have tips on how to install the fiberglass lid with a new windshield to top seal? The fiberglass top is sitting pretty high on the front end creating quite a gap (large enough to where the big u-shaped seal won’t cover). Just slowlygradually bolt the top down from back to front?
Everything to fix that mess on the frt of your engine . All Toyota parts. $35 shipped in the lower 48 $30 picked up in co springs
• Oil Pump Cover o-ring
• Distributor o-ring
• Front engine seal
• Oil level sensor gasket
Hi gang. Just want to say a quick apology to anyone that has answered on my previous posts. Life suddenly got in the way this year and kept me from the tank, but I'll be back in the game next month and will follow up on every post I started. I definitely appreciate all your help.
As I'm getting...
Getting ready to swap transmission/transfer between my 2013 and 2015 200s. Why? See my build thread. While I'm in there (my favorite words), I figure I might as well replace the rear main on the 2015. Do I need anything more than the seal itself (p/n 9031195013)? There is also a rear seal...