seal

Hey all, I’ve got a blown inner axle seal on the passenger side of my 94 LC. It’s pissing gear oil from the birf do I’m pretty certain that’s the problem. It’s only got about 10,000 miles on a full axle rebuild so I’m a little concerned that it blew out so fast. Question is : is it ok to...

I have been dreading replacing this seal for a while, so I will tackle this project in the winter and document it. I have had difficulty finding clear instructions on replacing this seal while the engine is in the vehicle. I understand I need to remove the radiator, bib, etc., so I have room to...

Spent the whole afternoon on a new bearing and seal. Cracked the extension housing on reinstall. Either misaligned the pump drive or the pump spacer fell down. Doggone it. Pics of the part that went well:

I'm about to go replace the output seal on my transfer case and trying to mentally walk through the job before tearing into it. Can the rear extension housing be removed with the crossmember still bolted to the frame rails? Planning to replace the output seal, bearing, snap rings, speedo...

Hi All - I did review the other posts on the form regarding this prior to install. I went to replace my valve stem seals today on my 1970 FJ40 (i.e. F155). Got to the first one, and I have two questions. First, the oem seal is the umbrella type. It is hard as a rock. I am assuming that...

I swear I’ve looked up and down here and on google for an answer other than make my own which is fine but wanted to see if any other thoughts. Definitely can’t find anyone selling this specific part. Only have a pic of the metal retainer clip and the form seal below but after removing drive...

I drained my tank in my FJ40. The rubber gasket is intact on the bottom of the tank (I left it in place, since it didn’t come off with the plug). Is the any sealant I can/should use on the plug when i reinstall it to ensure I don’t have leaks? Is anything recommended or useful? Thanks!

Hey does anyone have a Wits End inner seal offset driver I could borrow for a knuckle rebuild? I’d of course pay shipping and would be happy to pay for the time. This is my first time tackling this job and would feel so much better about setting that seal with the Wits End versus a harbor...

Had to remove taillight (someone dropped bulb inside and it was rattling..) Ripped seal (part of it stuck on a back door). Doesn't seem like it's available as a separate PN?

I’ll replace this seal going to the front driveshaft, but still leaks. Any tips on my next move?

Looking to purchase or borrow an inner axle seal driver from Wit's End, seems they're out of stock. I've got the inner axle seal out but noticed wear on where the birfield rides, hoping to hammer the seal in a tiny bit further in the housing. Any help is appreciated!

During routine maintenance at a local independent shop the technician reported the Rear main seal (crank seal) and valve cover gaskets leaking. How common is it for a rear crank seal to leak and need replacement? Vehicle has approximately 170K miles on it and has been driven primarily in the...

Replacing rear diff seal. Part number shows 90311-38028 in my parts book. I have one of those seals but it looks different from what is on mine. First picture is before I remove. 2nd picture is of the part I have. Can anyone tell me if this is correct part? I thought it was leaking but looking...

Replacing rear diff seal. Part number shows 90311-38028 in my parts book. I have one of those seals but it looks different from what is on mine. First picture is before I remove. 2nd picture is of the part I have. Can anyone tell me if this is correct part? I thought it was leaking but...

Quick write up about swapping winches. There's seems to be some misinformation out there that you have to pull the ARB bumper in order to remove the massive Warn M 12,000. This is not true, and it can be done by one person. The biggest hurdle seemed to be figuring out how to remove the vertical...

Looking for a place in the SF Bay Area for a 2008 LX570 head gasket seal. Looks like a head gasket seal is damaged, white fume from exhaust, coolant getting in. From what I understand this is a 4-6k job and it's mostly the labor that incurs the coat. I've called numerous shops but all of them...

What kind of grease (if any) do you use here?

Is there supposed to be a seal where the steering shaft comes out of the steering box? This is on a manual box, from a '70 fj40. My searches have turned up nothing, but seems there should be something there.

I have a 1974 FJ40 so I ordered rear axle seals at the Toyota dealership but I’m pretty sure they are the wrong ones. A couple of decades ago I swapped the differential from a 1970 parts truck. I can’t remember if I swapped the whole axle. I looked through the FAQ but didn’t see what I was...

I hoping someone has an offset axle seal driver that they would consider renting me? I'd obviously pay for the shipping both ways. I have my 80 tore apart at the moment and am ready to go back together with the axles but the offset seal driver I ordered from Wits End more than a month ago has...