https://cruisin4parts.com
I created a tool for fellow Cruiser owners to make finding parts faster and cheaper.
Enter a Toyota Part Number and you will see live prices from major suppliers from all over the world in seconds.
If you sign up for a free account, you'll automatically get enrolled...
https://cruisin4parts.com
I created a tool for fellow Cruiser owners to make finding parts faster and cheaper. Enter a Toyota Part Number and you will see live prices from 7 major suppliers from all over the world in seconds.
If you sign up for the free trial, you can save additional time by...
Haven’t driven in a week. Came home to a small oil puddle nearby the DS rear tire. Looks like oil is dripping off of the rear control arm. I can’t really tell what’s leaking because of the oily undercoating.
Before I start cleaning up a ton of oil, any ideas? AHC or Axle leak?
I have everything I need for my first (and the cruiser’s) transmission drain and fill. But, my local Toyota shop mailed the crush washers via usps and it appears they got lost.
So my question is… how important are the crush washers? 🫢
I’m thinking I do the job with the old crush washers and...
I’m visiting this weekend I think I’ve seen 5 different 100 series in the last 20 minutes.
Happy to see the cruisers are alive and well. I’m driving around a rented white 4 runner wishing I had my Cruiser! Cheers!
I need to put on a front plate but I can't find anywhere online what the mounting screw size is.
By the way, if you're like me and want to replace the rusted brackets the screws fasten to, here's the part number:
90179-06127
This one of the few things on my cruiser that keeps me up at night. There is a huge rust spot that is growing by the day and one near the edge of the door.
I’ve never done body repair and the only quote I got was “don’t bother, just buy a new door”.
Has anyone else had good luck finding...
I've been doing some reading and a lot of my symptoms point to a Pin 60 problem. It's consistent with the prius documents as well. I can repair or try to replace with this from Aliexpress.
My question is, are 2006 Cruisers affected by the same Pin 60 problem? I thought Toyota fixed the Pin 60...
Well last time it was my fault, this time it was Toyota’s fault. I ordered the belt mouldings for my 100 series and received 2 80 series ones. See below for the parts.
I threw the one bag before realizing it was an 80 part again 😑. Apologies I don’t have the bag with the part number but I’m...
Go from a cut glovebox support to a fully functional one again
If you have cut the plastic glovebox support bar to service the evaporator, this bracket is for you. Normally to repair the severed support bar, you'd need to purchase some sort of metal bracket and attach 2 or 4 screws to hold the...
Here is where the sensor was clipped when I pulled the evaporator out yesterday. The FSM isn’t super clear where to put it other than a vague drawing.
I do know it has to go on the left side (closest to the driver) of the evaporator so it can connect to the harness nearby.
Does it really...
Has anyone completely replaced their rear AC lines with some after market solution like Cold hose? Looks like they take your hoses and create new.
Im leaning towards that because:
1. My rear lines were capped by previous owner so I don’t know which parts actually leak. Plus, the lines have...
This is not my listing, it just popped up on my iSeeCars alerts nearby me and figure I'd post it in case someone is looking for an expensive 100.
48k miles. Looks like a Georgia truck :eek: . Asking $49,950.00. Wow. At that point you gotta get a 200, right...
I posted in another thread about wind noise, but I wanted to start a new thread rather than fully hijack. I have an aftermarket PGW windshield installed by the PO. I have wind "rushing" noise at high speeds or if the wind blows at high speeds. It's loud enough I have to crank the music up to try...
Just use zip ties!
Jokes aside. I cranked a little hard on the heim joint and broke it. It sucks, don’t do what I did. The adjuster nut was worn down so I had to use a vise grip to turn it and it broke.
New one on the way, $80 from Toyota since Partsouq is sold out of that side for some...
I'm almost certain I saw someone mention this method in one of the million AHC-related threads out there, but couldn't find it.
I recently replaced the globes back in August and paired with the new control arms, the ride was super smooth.
However, sometimes I notice the Cruiser's ride is...
My cruiser is up at Garden state undercoating in New Jersey. Another member got it and evidently a ton of FJ Cruiser and 4Runner guys in the area use them. I wanted to share some photos of the progress.
He cleaned, grinded, primed, painted, and is now coating with fluid film.
I know this...