Search results for query: *

Forum search Google search

  1. Eurasiaoverland

    Inner window felt weatherstrips

    Does anyone have a source for generic rubber and felt weatherstrip (the rubber itself) which is used on the door inner weatherstrips? 68170-90A01 is the Toyota part for the front windows with a single glass (i.e. no quarter ventilation window) and 'full' trim, i.e. a door card which comes up to...
  2. Eurasiaoverland

    Wanted  60 or 70 Series PTO worm gear

    Looking for a worm for an HJ61 PTO winch. I think most 1984+ 60 and pre 1990 70 Series winch worms are the same, not sure. 40 Series definitely not compatible. Right handed thread. P/N 38135-60090 Postage to Houston, TX. Thanks EO
  3. Eurasiaoverland

    PTO box O ring sizes

    Does anyone know the size of the O-rings used in the 60/70 (and probably 40) series PTO boxes? There are two sizes - one for the input gear shaft and lever shaft (3 in total) and one that lives inside the case where the shift shaft comes out of the front of the unit. Unfortunately they are...
  4. Eurasiaoverland

    Original factory under-arch colour

    Body-off restoration of a 1989 BJ60 in Toyota white 048. Can anyone tell me what the original factory colour was under the wheel arches? The factory underbody finish on mine is a neutral grey. The rubberised stonechip is a white compound. Were the arches left in unpainted stonechip? Or also...
  5. Eurasiaoverland

    R134a receiver dryer

    I'm adding AC to a BJ60 that never had it and am looking for a good accumulator-dryer unit. I have Denso 478-0101, however I have read very credible information on this site stating that the AH5 desiccant used in this unit is for R12 (only) and will not work for R134a. I don't believe that...
  6. Eurasiaoverland

    60 series glow plug relay assessment

    Below is a picture of two identical glow plug relays. On the left is a brand new (actually 30 year-old NOS) version and on the right is a relay from my BJ60. The car has well over half a million kms and is an indirect-injection diesel, so glow plugs will have been used for every cold start...
  7. Eurasiaoverland

    Part number for standard Toyota water hose

    I'm upgrading my BJ60 from a 3Bii to a 15B-T. Although the swap is very straightforward, I need to custom make some hoses for the install. One thing I'm after is the thinner water hose, the size which is used for the ACSD or turbo water hoses on, for example, the 1HD engine. It's about 16 mm/...
  8. Eurasiaoverland

    Door card restoration

    My front door cards came with speaker holes cut in courtesy of the previous owner. I managed to swap them for a pair of unmolested but shabby door cards. On the 'new' door cards, the vinyl covering is pretty much perfect, but the fibreboard (not sure what it's called in the US) is warped and...
  9. Eurasiaoverland

    Late 60 Series PTO pillow block brackets

    I'm looking for a picture, if possible, of one of the PTO drive shaft pillow block brackets from a late 60 Series. There seem to be multiple arrangements of drive shafts and brackets. I'm not sure when the change occurred, probably late 87 with the facelift, but I have seen an early (1984ish)...
  10. Eurasiaoverland

    Clean coolant passages with vinegar

    I recently bought a used engine from a Japanese half-cut. It's in great condition, except that it seems to have been left long-term with just a trace of coolant/water in, and the inside of the coolant passages is rusty. I have flushed out a lot of rust sludge with a hose, but I am still concened...
  11. Eurasiaoverland

    FJ62 pressure port brass seats

    I'm rebuilding my 1989 steering box (BJ60 but basically a RHD version of the FJ62 box). I have all the seals/O rings/teflon rings etc except the pressure port seats. Looking globally, (things might be different in the US), three different parts were used for the seats: Early 60 Series (80-83)...
  12. Eurasiaoverland

    14B-T specs

    The 14B-T is maybe my favourite B engine and during much internet trawling, I finally came up with some official-looking specs. It comes from a Taiwanese customs website, looks to be an official document for import/registration in Taiwan. The 14B-T was mostly sold in Japan in 24V Dyna/Toyoace...
  13. Eurasiaoverland

    Wanted  14B-T intake manifold air intake and crossover

    Looking for an air intake for a 14B-T intake manifold (not the manifold itself). Can be posted to Houston, TX. Addresses in Australia and Europe also available.
  14. Eurasiaoverland

    Does anyone have any experience of the 8-valve 15B-T?

    Just to be clear, I am not looking for information on the 15B-F, 15B-FT, 15B-FTE or 14B-T. These engines were all sold to public with plenty of information out there. I am after information on the 15B-T, which was an early (ca. 1995), 8 valve 15B that externally is a 14B-T but has apparently...
  15. Eurasiaoverland

    Does anyone have any experience of the 8-valve 15B-T?

    Just to be clear, I am not looking for information on the 15B-F, 15B-FT, 15B-FTE or 14B-T. These engines were all sold to public with plenty of information out there. I am after information on the 15B-T, which was an early (ca. 1995), 8 valve 15B that externally is a 14B-T but has apparently...
  16. Eurasiaoverland

    Reading engine block casting numbers

    This is on the side of my 3Bii block. Original engine, vehicle construction date 07/1989: Now I read this as '9' meaning 1989, and '6' meaning June. or could it be Week 6 of 1989? No idea what UB means! Wondering if anyone knows more or can correct me? Before anyone chimes in with it, no...
  17. Eurasiaoverland

    Could someone with an 08/1987 to 12/1989 non-US 60 Series please check their brake pipe routing?

    I have a master cylinder/booster with a brake proportioning valve as per the first picture in this thread. If you have a 1987-89 non-US 60 series with front disc brakes and no rear load-sensing proportioning valve, could you please tell me which output from the proportioning valve goes to the...
  18. Eurasiaoverland

    Brake proportioning valve - how does it work?

    I'm in the process of rebuilding a (non-North American) 1989 BJ60. The vehicle was originally equipped with drum brakes on all wheels, so never came with a brake proportioning valve. I am adding a year-correct, factory original brake master cylinder, dual-diaphragm booster and proportioning...
  19. Eurasiaoverland

    Has anyone bought the turn signal/wiper stalk decal set on ebay?

    I have a indicator/wiper stalk assembly with the graphics mostly worn off. I am looking at this kit on ebay (I am RHD but there are LHD versions as well): https://www.ebay.com/itm/174587288004?hash=item28a63699c4:g:kOQAAOSwFSFhuLS2 I actually bought this set back in 2020 and what arrived was...
  20. Eurasiaoverland

    Cleaning oil from speedometer

    This had me sratching my head for a while - I had oil leaking up the speedometer cable into the cabin, starting from the back of the speedometer and creeping all along the bottom of the dashboard panel. So the back of my speedometer is covered in oil. Ideally, I would like to clean it up and...
Back
Top Bottom