So I let the snowball get away on me and am remanufacturing my 22re engine.
The engine was my daily driver for years with 5.29's and 35's and I live in a mountainious city. The engine basically idled at 3k rpm and shifted regularly at 4500. Albiet some occasional hot ratttle clatter start up...
Looking into this option as my onboard air system for filling tires.
CO² might prove difficult to get but I havent exhausted my options yet. But reading into it, is there any particular reason CO² is traditionally used? I would imagine it is cheaper than N², although it kind of seems like a...
Hey, looking for some insight on getting frame shackle tubes installed square to the world.
What is the best way to get the tubes perfectly? aligned to the front hanger and symmetrical from left to right?
This isnt my standard M.O behind the wheel, but it was eye opening to the lack of functionality in my current set up.
Open diffs, pretty violent wheel hop front and rear.
I was in 4wd low range.
5.29 gears
35" tires at 27psi front 25 psi rear
Chev 63 rears with bilstein 5100's mounted at a...
I have the height I want with a 3+1 chev 63, a 2" lift block, and an 8" shackle. The truck has a fairly weighty tube deck. I want to ditch the block but keep the height. Not sure if I need it stiffer or not.
What is an "'add a leaf"? Is it different than going to my local spring shop and...
Ive got a question about the theory on OE seals and gaskets.
Ive read a lot of "use OE Toyota main seals, head gaskets, wheel bearing seals" etc.
And at $10-20 a pop for seals (say a trans seal or rear wheel bearing seal) and $50 for say a head gasket, it doesnt really break my budget if its...
Does anyone have a picture of a non molested '86-'88 pick up or '86-'89 4runner rear axle?
I'm trying to figure out the stock parking brake route/mounting situation and what parking brake cable I need for my rear axle. My parking brake bell cranks are on the bottom of the backing plates. And...
I want to put a rear winch on my '85 pick up. Does anyone have some insight or experience on how to anchor off the rear of the frame? The truck has a flat deck on it, so working around the stock box and/or stock rear bumper is not an issue.
Ideally I would like to bolt a winch mount plate to...
In the FSM for a w56 trans, in the transfer adapter, it refers to a "reverse restrict pin". It has a spring loaded lever on it that interfaces with the shift rod. What is the function of the reverse restrict pin?
Its the thing in the bottom right of the housing pictured.
Re-doing the steering box mount on my '85 truck. Prev owner didnt sleeve the frame so nows the time to fix it. Already looks like he had it shoved all the way forward. But the plates were straight cut at the ends so I cut those off for radiusing. Redoing the whole set up at this point.
Anyone...
Got a thread going in the '95 older tech forum. Question might get some more exposure here.
We would like to know the rear driveshaft length.
Things we'd like to know:
Year of truck
Engine size
Trans manual or auto
T case Multi Mode or non
If stock ride height or lifted
Length of shaft from...
Title pretty much sums it up. How important are the gaskets for OE trans and t case function/reliability?
From what I visualize on the trans if I run without the input bearing retainer gasket that will tighthen it up a bit. If I run without the front half gasket to the centerpeice it will...
I'm fully in the rabbit hole of frame repair.
I was initially just going to slap a couple patches in the frame where I could see that the inside was blown out. (Usual suspect area right around the spring mounts at the cab)
Couldnt leave it well enough alone considering how much time and...
Anyone know the fueling strategy? More specifically, how does the base fueling map compare to open loop vs closed loop fueling?
Is the base map = to open loop?
Are closed loop +/- trim values always less than open loop?
In open loop, is the fuel quantity always greater than the fuel quantity...
Why does my 22re sound like it has some rattle clatter happening in the front end?
If the guides are fully intact, is it possible for the chain to be loose enough(either from wear or a malfunctioning tensioner) to have the chain clatter/rattle? Timing set has been allegedly replaced within the...
When does the stock 22re cam turn on/open up?
Not sure if my cam is OEM....but my 22re has a long tube header 2 1/4 collector into straight back 2 1/4 tube with a muffler along the way. Has a fairly smooth idle but sounds good at idle and sounds good opened up.
Motor turns ON like a light...