What have you done to your 200 Series this week? (16 Viewers)

[tbisaacs]

I haven't tried this, but it seems you can make an aftermarket 12v function in place of the factory 6v for a few bucks.

Toyota-4Runner.org

The Largest 4Runner Community in the World

www.toyota-4runner.org

i wondered about this. Only potential issue is that the front and side cameras are wired together. My front camera is unplugged and that also disables the side. Would just need to sort out wiring.

 

[DJCloz]

Would like a pic of your lowered license plate..

@Mago Check it out

 

[mbennett22]

Installed a single Dobinson drawer from my 100 into the 200. Perfect!

View attachment 2515308View attachment 2515307View attachment 2515309View attachment 2515310

Nice, I have been thinking about doing one drawer so I can keep at least one rear seat. That way I can keep my sanity on long trips with the two kids! LOL

 

[mmorgan24]

Nice, I have been thinking about doing one drawer so I can keep at least one rear seat. That way I can keep my sanity on long trips with the two kids! LOL

Ditch the kids, you'll thank me later ... ...

(says the father of two semi-adults)

 

[jrmudder92]

Getting into the Christmas spirit at Uwharrie.

 

[LC200JG]

Getting into the Christmas spirit at Uwharrie.

View attachment 2518617

View attachment 2518618

View attachment 2518619

View attachment 2518620

Love it! I was afraid I was one of the only 200's at Uwharrie!

 

[jrmudder92]

Love it! I was afraid I was one of the only 200's at Uwharrie!

You are the only one with all the body damage
ONSC has a few 200 that go out there

 

[LC200JG]

You are the only one with all the body damage
ONSC has a few 200 that go out there

Dude, I earned that body damage. LOL!

 

[jrmudder92]

Dude, I earned that body damage. LOL!

That you did. No way I would do it haha ill stick to the backside

 

[LC200JG]

That you did. No way I would do it haha ill stick to the backside

I really love it. My body damage is in line with what the truck is meant to do. My own personal thing and I’m weird I know. I love it. I would like to do it again. Pretty sure I should go on top!

 

[jrmudder92]

I really love it. My body damage is in line with what the truck is meant to do. My own personal thing and I’m weird I know. I love it. I would like to do it again. Pretty sure I should go on top!

I respect that more than you know. Honestly

 

[NoClue]

Got in my ditch lights for mounting but need recommendations on hood mounts for 2018 model. Any thoughts?

200 Series Land Cruiser Light Brackets | CBI Offroad Fab

This year we were invited to work on the CBI Offroad Fab and Lexus J201 Concept Build for Lexus and XOverland that will debut at the 2020 Rebelle Rally.

cbioffroadfab.com

 

[NoClue]

Completed my drawer install. Went well, told my self to take my time and not get frustrated or impatient. Easier said than done, but it went smooth. **Warning** everything on the drawers is sharp ( I have the bandaids and tetanus shots prove it...) Seriously, be careful moving to quickly on screwing or unscrewing the bolts will bite you. Also, thanks to JLH for letting me know I need to get some Hex Socket Set, that saved e a ton of time. Only major issue is one of the screws attached to the mounting plate was too tight or cross threaded, I had to drill out. Other than that it was a great project, and was a real sense of accomplishment when everything lined up and "worked." Not too mention they are going to work out great for my need in the future. Have a good rest of the weekend.

Very nice, are the tops of the drawers slide outs? Also, when the middle row is folded down is it level with the top of the drawers?

 

[jrmudder92]

Also learned how to count. But only to 6.

 

[Mago]

@Mago Check it out

Well done, thanks!
Did you purchase that license holder or fabricate it? If purchased could you provide a link?

 

[reddog90]

Started installing an Ironman FCP lift and SPC UCAs.

 

[reddog90]

I can't recall if I posted how I did this. I'll try to dig it up. In reality all I did was use a dremel to cut the extra plastic away. You could also probably do this with a sharp Exacto knife or a good set of scissors or tin snips and maybe some sand paper just to file down the edge.

Here's a photo of the result.

Trimming bumper plastic around hitch

• linuxgod
• May 12, 2016

Trimming the plastic required to allow my master lock locking hitch pin to fit-

Edit: This is the original link, but it's not much more helpful than what I just described above

What have you done to your 200 Series this week?

forum.ih8mud.com

Overall it's a very easy modification.

I also have a 2013 LC200, and honestly I am at a loss to understand why all this plastic cutting is necessary.

Here are some pics of my unadulterated hitch area with an easily accessible locking pin:

View attachment 2408428
View attachment 2408429
View attachment 2408430

What am I missing?

BTW, here's a link to that locking hitch pin: Master Lock Receiver Lock, Stainless Steel Barbell Receiver Lock, Fits 5/8 in. Receivers, 1469DAT

HTH

I ordered this exact locking hitch pin after skinning my middle finger trying to get a standard bent hitch pin out over Thanksgiving. I ordered the 3.5" stainless version because that's what it looked like you had in this picture This hitch pin still doesn't clear the plastic on the red (non locking) side without binding up. And I can't get the locking mechanism on the other end of it either. I was going to try trimming plastic away before returning it, but just wondering if I may have ordered the wrong variant?

 

[gaijin]

I ordered this exact locking hitch pin after skinning my middle finger trying to get a standard bent hitch pin out over Thanksgiving. I ordered the 3.5" stainless version because that's what it looked like you had in this picture This hitch pin still doesn't clear the plastic on the red (non locking) side without binding up. And I can't get the locking mechanism on the other end of it either. I was going to try trimming plastic away before returning it, but just wondering if I may have ordered the wrong variant?

You ordered the correct version. As my pictures clearly show, it fits on my 2013 LC200 - no idea why it doesn't fit on yours

 

[Bullgump]

200 Series Land Cruiser Light Brackets | CBI Offroad Fab

This year we were invited to work on the CBI Offroad Fab and Lexus J201 Concept Build for Lexus and XOverland that will debut at the 2020 Rebelle Rally.

cbioffroadfab.com

Much appreciated. Ordered.

 

[Jelder]

This mod is about as unsexy as they get, but I'm doing my best to winterize my '13 LC that I imported from N.O. to Michigan. In addition to getting it rust proofed, I made sure the KDSS shutter valves turned, slathered them with marine grease, and then covered the window with a couple pieces of heavy duct tape. I know it's not going to stop all the snow and salt from getting in, but I'm hoping if I keep my eye on it over the winter that the valves will be OK come spring- and then it's 2" lift time!