Trail Tailor Offerings- Racks, Sliders, Control Arms and Misc

[TRAIL TAILOR]

Another (no arm) basic rear 100 rear.

Jason

 

[TRAIL TAILOR]

A little 100 fab.

Rears, fronts, sliders and starting a short run of UCAs @jLB twisted my arm for another set.

AND NOTICE.... as always... TT products are built using domestic USA materials.

Jason

 

[jLB]

A little 100 fab.

Rears, fronts, sliders and starting a short run of UCAs @jLB twisted my arm for another set.

AND NOTICE.... as always... TT products are built using domestic USA materials.

Jason

View attachment 3287547View attachment 3287548View attachment 3287550View attachment 3287551

Hmmm…

With that many UCAs being built, maybe I need another set to replace my son’s SPC UCAs

 

[TRAIL TAILOR]

Hmmm…

With that many UCAs being built, maybe I need another set to replace my son’s SPC UCAs

2 sets available. You've run all MFGs through the works and coming back for TT seconds... just saying!

J

 

[jLB]

2 sets available. You've run all MFGs through the works and coming back for TT seconds... just saying!

J

While I might prefer having the OE style brake brackets, the misalignment joints, in place of bushings (that are put under stress in setting the alignment), just makes sense, not to mention that they’ve been noise & problem free, and while I’ve not yet needed replacement parts, I understand that they’re readily available (from multiple sources). What’s not to like?

Not to mention that I have two other manufacturers “orphaned” UCAs, one of which gives a on support/parts, other than offering to sell me the upgraded UCAs at full price. Oh wait, I guess I did mention that.

 

[jflone]

2 sets available. You've run all MFGs through the works and coming back for TT seconds... just saying!

J

2 sets available. You've run all MFGs through the works and coming back for TT seconds... just saying!

J

I'm interested...details on the UCA? Ball joint pressed in? 555?

 

[jLB]

I'm interested...details on the UCA? Ball joint pressed in? 555?

Not Jason, and therefore not authoritative, but mine have had the ball joints pre-installed. It’s my understanding that they are the same as 07-09 Tundra ball joints, and 555 does offer those, but I have no idea what Jason installs by default. It is my understanding that the “bushings” are Currie Johnny Joints, I assume that they’re a standard catalog item, but don’t know that for sure.

 

[TRAIL TAILOR]

100 Series bolt on tire carrier prototype in the works.

Will offer a single and dual arm option if enough interest.

J

 

[LandTuna]

100 Series bolt on tire carrier prototype in the works.

Will offer a single and dual arm option if enough interest.

J

View attachment 3288183View attachment 3288184View attachment 3288185View attachment 3288186

What’s your price point going to be for these you think? Looks awesome.

 

[TRAIL TAILOR]

What’s your price point going to be for these you think? Looks awesome.

Once I get the final pieces dialed in I will send off to the laser shop for a quote.

Single arm-- shooting for

DIY- 775.00
Add 300.00 for welded out

Jason

 

[LandTuna]

Once I get the final pieces dialed in I will send off to the laser shop for a quote.

Single arm-- shooting for

DIY- 775.00
Add 300.00 for welded out

Jason

Not bad at all, definitely interested!

 

[TRAIL TAILOR]

100 SAS custom axle build. Stretched 5" and custom RCV CrMo inner axles.

J

 

[MysteryMachine]

100 SAS custom axle build. Stretched 5" and custom RCV CrMo inner axles.

J

View attachment 3295497View attachment 3295498View attachment 3295499View attachment 3295500View attachment 3295502

What will be the price on these ? Would still need your SAS bracket that you sell as well?

 

[TRAIL TAILOR]

What will be the price on these ? Would still need your SAS bracket that you sell as well?

Ballpark with extended inner RCV axles (options vary) 2500-3200.00 You will need the bracket kit less the axle coil buckets.

Or I have machined 2.5" knuckle ball extenders so you can use an 80 housing. 640.00 extenders and axles (still need full SAS bracket kit.

Jason

 

[TRAIL TAILOR]

Want to thank all the 100/470 customers that participated in the Hidden Winch Mount FaceBook buy.

All shipped today!

Jason

 

[TRAIL TAILOR]

 

[MongooseGA]

My mother will be excited about this.

 

[FrankieJoe14]

My mom was asking for a good deal on a rear bumper

 

[Keowee]

Mama didn't raise no fool.
Put a bow on it.

 

[TRAIL TAILOR]

TRAIL TAILOR is now a Dobinsons dealer. If there is any interest please PM or email me.

Free shipping to your door (lower 48)

Jason