Local For Sale/Wanted Section! (1 Viewer)

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Doors

I've got a pair of pre 74 fj40 front doors for sale. Doors are red driver side door dented towards bottom. No rust. $150 obo. 75 and newer hard top with amby doors. Doors are black have rust on bottom, repairable. Top has no rust. $400. stock 4 speed bellhousing $25. Other parts laying around ask and I can take a look. Thanks, Dan. 610-360-9549 best to reach me by phone.
 
Need FJ62 catalytic converter

Hildy or whoever- a guy from Virginia asked me if anyone has a used catalytic converter for an FJ62. I thought maybe Hildy might have something or maybe someone else. Can anyone help? let me know. Thanks, Gary S
 
Dana 60s - $400 - Ephrata

All,

I am moving next week and have a set of D60s sitting in my garage that I would NOT like to take with me!

The front is a Chevy (Passenger side drop) dually axle converted to SRW with Dodge parts - and with 35 spine drive flanges. It is a 4.11 diff, has no brakes on it (I was planning to use 3/4 ton brakes), 35 spline inners, 30 spline outers.

The rear is a Ford 3/4 ton full floater. I don't recall the ratio on this one but I do know it is not the same as the front. It also has no brakes and would need bored out to have 30 spline shafts (there used to be a few boring tools floating around locally).

I don't have pictures, but they are as-pulled (not painted or cleaned) and have a light coat of smurf blue paint on them.

CAZ
 
Caz, what does the front Dana 60 need to run. I am very interested.
 
It needs brakes, histeer arms, 35 spline outer shafts (similar to the birfield on a Toyota), u-joints, and some TLC.

You would likely want to get a conversion kit for smaller brakes on it. The 1 ton brakes are expensive - not to mention HUGE! You need smaller brakes to fit a 15" wheel.

OLD pictures - I had them mounted up and then bought my 40 and scrapped the project. They are FULL WIDTH axles. They would only be reasonable on a Toyota with something like the Hummer wheels I had (7" backset").

main.php


main.php
 
Let me get some things figured out, I would need to unload my Toyota front axle that I built for my 4 Runner to get this in its place. I would be looking at running either H1 or H2 rims with 42" Iroks or 40" LTBs on the 4 runner.

Did you clip the low steer mounts off the knuckles? That would be my biggest issue since I am planning on low steer with just crossover since I am only going to be running about 2" of lift.

When do you need these gone by?
 
Last edited:
22r for sale

22r, i think its from an 85, right now its a long block, but i have the intake/carb, exhaust manifold, flywheel/stock clutch, distributor, and i think the rest of the accessories for it(ps pump, alt, starter, etc...)

the oil that i drained out looked ok, not sure on how many miles, the valve cover is really clean , and i have some extra new gaskets and seals for it

located in northumberland, pa 17857, but i can get it to the first rcrocs for free, or to A-Z in schuylkill haven on any weekday

$100, i also have a 1000lb capacity engine stand that can got with it for an extra $50, it just needs a new caster
 
sold

FS my Green 94 cruiser brown cloth interior. 187K on the clock. Runs great , kyb shocks and 315 (33") BFG mt with less than 20K on them. Good brakes all around, Pa inspected. newer rotors up front.

Bads. It will need a birf job in the future, kinda gooey under there. I do have a set of low millage birf and axle to swap in and the rest of the parts to do a quick birfield job. It also has a leak at the O2 sensor. I had one fixed at a local shop but he did not do the other. I have a set of really nice down pipes included. Just swap them in. I do not know if the headgasket was ever done. I have not observed any of the signs that it needs it. It does leak a bit of oil around the front of the valve cover. It's not perfect there's a few little dings and some light scratches.

I also have a spare rear hatch and all the stuff in there, I have the original running boards. I did have to fix the one rocker corner but it came out good with nice clean metal. no other rot.




I'm in pa 18707

bob
 
Last edited:
Doors FJ60

I have a pair of front doors fro an FJ60. The doors are in great shape (silver). Both doors include weatherstripping, window mechanisms, and glass. Asking $475.00 for pair. Any questions just ask.

I am in Dillsburg, PA.
 
help me i swapped my rear aussie locked third to the front and welded the new rear. problem is i cant find my old, i believe pinion spacer, it keeps the c-clips from falling out anyone got one they will let go cheap I wanted the truck done for this weekend oh well.. Just did a so and itching to beat it by the way its a n 87 fj60 if it matters and im in shrewsbury pa. help a brother out thanks guys


Bryon
 
Peg Perego Gaucho

My son (3) and I were looking through old pictures and he saw A photo I took of my red 40 now sold and said Daddy's mud truck, it's gone now (ouch), now we both like the 80 but is is not a 40.Though he still likes mud trucking in it! I have a 40 frame/semirolling chasis, thanks to Gary. But, I need a Peg Perego Gaucho to get by with my son's cruiser addiction, if anyone sees or has one, my son and I will appreciate it.

Thanks, M. Reed 610 6036861
 
You must log in or register to reply here.

Similar threads

Crusha
Anyone want to admin the Facebook page?
Replies
10
Views
630
YotaFun
YotaFun
Mixelplix
Scranton area - FJ80 guy wants to ride in an FJ40
Replies
4
Views
817
brian
brian
Obioban
Looking for a shop that can leak free install a windshield in a 100 series within driving range of SE PA.
Replies
2
Views
253
Red Beard
Red Beard
Offline
Wheeling in Wharton State Forest (NJ)
Replies
7
Views
1K
PhuckItImDone
PhuckItImDone

Users who are viewing this thread

Total: 2 (members: 0, guests: 2)

Share this page

Back
Top Bottom