- Thread starter
- #21
Build thread: Project rusty 75 (1 Viewer)
- Thread starter hedgehog23
- Start date
This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.
- Thread starter
- #22
engine removed and disposed of today. glad its gone, i can finally pick up my new engine. i don't have room in the garage for both.
The PO used some sort of undercoat on the firewall and fenders. going to be a pain stripping it all but should be little rust.
also removed the windshield. not a fun job. found more rust (big surprise
) id like to replace the dash pad mount , i know some guys remove them for a box install so maybe ill post a want add. If you have one PM me.
The PO used some sort of undercoat on the firewall and fenders. going to be a pain stripping it all but should be little rust.
also removed the windshield. not a fun job. found more rust (big surprise
) id like to replace the dash pad mount , i know some guys remove them for a box install so maybe ill post a want add. If you have one PM me.
- Thread starter
- #23
picked up the 3b with 4 speed, and the mini truck front axle from a friend last weekend. engine is cleanish and looks good. buddy said it ran well last summer when he pulled it.
currently looking for a 12v starter motor to convert the starter from 24v to 12v
currently looking for a 12v starter motor to convert the starter from 24v to 12v
- Thread starter
- #25
Great thanks for that twoyotas will make fabing up the floor a lot easier to do with measurements
no problem.
you've got your work cut out for you! But it looks like the project is in capable hands.
Huzzah for the salvation of another 40
you've got your work cut out for you! But it looks like the project is in capable hands.
Huzzah for the salvation of another 40
I've never even seen an fj40 for $400, sweet job, keep these baby's on the road!
- Thread starter
- #28
well got the engine mounts fabricated today, there not 100% burned in place yet but enough to hold her in place.
there made of 3/16" x 4" plate. just cardboard cut outs then transferred them to the steel. made a sister frame plate (8" long) to spread the load.
looking for a trany cross member to finalize the mounting install. if i cant find one ill make one up.
The sharp eyes in the bunch might notice that the drivers side rubber mount isn't right. I only have one proper mount for the bj , so i used a fj rubber puck and a few washers to hold the spot for the mount work.
Plans are to assemble the under the hood equipment , like battery tray, throttle cables , air cleaner ect. Then tear it all down again and finish the paint and body work.
there made of 3/16" x 4" plate. just cardboard cut outs then transferred them to the steel. made a sister frame plate (8" long) to spread the load.
looking for a trany cross member to finalize the mounting install. if i cant find one ill make one up.
The sharp eyes in the bunch might notice that the drivers side rubber mount isn't right. I only have one proper mount for the bj , so i used a fj rubber puck and a few washers to hold the spot for the mount work.
Plans are to assemble the under the hood equipment , like battery tray, throttle cables , air cleaner ect. Then tear it all down again and finish the paint and body work.
BDSeff1fitty
1987 Toyota 4Runner
sent PM for measurements
Updates? Nice work, good inspiration. How did that sill work out for you?
- Thread starter
- #31
soon very soon ill update this thread
iv been dealing with my 98 tacoma. rusted frame. Toyota bought it back from me! soon as that deal is done and im in the MR2 that i picked out ill have some time
but
3b is in
h55 is in
rear body panels eta 2weeks
ct26 waiting install
starter , found
12v glow plugs. installed
12v alternator , on the look out
wiring harness is out and im going threw it in the gun room/workshop
dash is striped down and all the switches have been reconditioned. ill be fixing the frame and coating it very soon. shopping for a turbo manifold
iv been dealing with my 98 tacoma. rusted frame. Toyota bought it back from me! soon as that deal is done and im in the MR2 that i picked out ill have some time
but
3b is in
h55 is in
rear body panels eta 2weeks
ct26 waiting install
starter , found
12v glow plugs. installed
12v alternator , on the look out
wiring harness is out and im going threw it in the gun room/workshop
dash is striped down and all the switches have been reconditioned. ill be fixing the frame and coating it very soon. shopping for a turbo manifold
Last edited:
- Thread starter
- #32
picture of said mr2
- Thread starter
- #33
Looking at ordering a suspension kit this week. Looking at a 2.5" kit by Hellcreek. they tell me that the 2.5" kits are back ordered for 4-5 weeks.
I like the look of the 4" kit but worry about the overall height of the fj with 33" tires when im done. Dont know if it will fit in the garage when im done.
can anyone take a measurement of there fj with 33"'s and 4" kit for me ?
I like the look of the 4" kit but worry about the overall height of the fj with 33" tires when im done. Dont know if it will fit in the garage when im done.
can anyone take a measurement of there fj with 33"'s and 4" kit for me ?
Nice work, looks like a great project! Keep up the good work. Where in Ontario are you. I am in Detroit.
Matt
Matt
- Thread starter
- #35
Im just east of Toronto. The project is slow going between work and money/life
Should have some progress pictures soon.
Should have some progress pictures soon.
I measurement is 11 7/8. J is 3 1/4. K is 4 1/8. Measured from my '75.
- Thread starter
- #37
Thanks Nikp if i posted pictures of how much of my bed is missing and how "floppy" it is right now, it would frighten too many people
- Thread starter
- #39
1000$ with a 4 speed and transfer case. i sold the 4 speed for 250$ and found a h55 for 300$
- Thread starter
- #40
anyone help me out with the wiring harness. im going threw and removing the radio/emissions gear and relocating the starter wires for my 3b conversion.
anyone know what these two are for? the big one was real close to the emission computer if that helps.
anyone know what these two are for? the big one was real close to the emission computer if that helps.
