- Thread starter
- #241
I saw somewhere about sealing a couple of the bolts on installation. Can anyone elaborate or point me in the proper direction on this?
Bought My First Pig (2 Viewers)
- Thread starter FLMikem
- Start date
This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.
I don't know about sealing a couple of the bolts, but be careful putting the timing cover bolts back in. They are not all the same length. I seem to recall there are 2 or 3 real short ones and they need to go back in from where they came. Their holes are the ones that are directly over the gears.
- Thread starter
- #243
Yeah I have those and was wondering about that actually. Good to know.
This page is helpful. The #2 bolts are the short ones.
www.sor.com
Land Cruiser Engine Timing Cover Components
Land Cruiser F 2F 3F and 1FZ time plate and timing gear cover, timing cover seal and gaskets
- Thread starter
- #245
All back together. Had a little squeeze out despite my best efforts. Oh well. How flush is the crank seal supposed to be? Couldn't get it any more flush without needing a press. All lubed up as too.
OlYellr
SILVER Star
I need to refresh this thread quickly - lots changes fast - I had to do this two times with the bolt length/seal the threads vs read the 2F FSM and do it once. Here is it for any future reference.
- Thread starter
- #247
This is what I was looking for regarding sealer on the bolts! Thanks. I figured it out through some other online posts. It makes sense when you start installing the bolts. Some aren't long enough and some are too long and when it's in the right spot it's clear it's supposed to be there.
- Thread starter
- #248
So the new balancer is pressing on but it's giving me some trouble. Got it on and decided to take my chances and run the last little bit in with the crank nut. Before the nut took any torque, wasn't touching anything it stripped itself. I about crapped myself but luckily the crank threads are fine. Hard steel crank vs spongy steel nut. The nuts gonna lose ever time.
I "felt" my way around the crank as best as I could with a pick and the threads on the crank seemed alright. So now I gotta get another nut. All this isn't too surprising as the nut struggled to come off once the torque was broken on it in the first place. Are there any other alternatives for crank nuts out there or just source another one?
I "felt" my way around the crank as best as I could with a pick and the threads on the crank seemed alright. So now I gotta get another nut. All this isn't too surprising as the nut struggled to come off once the torque was broken on it in the first place. Are there any other alternatives for crank nuts out there or just source another one?
OlYellr
SILVER Star
when I was doing mine 6 month ago, I ended up sourcing.. For what it is worth.
- Thread starter
- #250
Good to know.
Edit: Just sourced along with some other bits and ends that I was procrastinating getting.
Last edited:
- Thread starter
- #251
I'm still struggling to get enough "whack" to drive the pulley on. Got about a 1/4in left. I was able to hog out the bad threads on the old nut and it now makes a decent enough driver that I can hit and it's working kinda.
Side note: that nut is soft! It won't take much of anything to dent/chip/simple/bend it.
Side note: that nut is soft! It won't take much of anything to dent/chip/simple/bend it.
Maybe get a tool like this, they do work.
www.eastwood.com
Eastwood Harmonic Balancer Installer
Don’t risk Damaging your Harmonic Balancer or Oil seal.
- Thread starter
- #253
Maybe get a tool like this, they do work.
Eastwood Harmonic Balancer Installer
Don’t risk Damaging your Harmonic Balancer or Oil seal.
If only. It seems that s for an internal thread crank (balancer bolt) instead of Toyotas external thread (balancer nut) crank snout.
I'm wondering if a new bolt would have enough hardness to help pull the balancer on without stripping again.
Try a new bolt. Fsm calls for 140 ft lbs I believe. If it were me, I’d get as close to that as possible without stripping the nut and call it good. When I took that nut off a 3fe, it was impossible without maneuvering a long breaker bar against the frame and turning the engine over via the starter. How in the world is that much torque required on a keyed balancer???? Crazy.
I didn't think about that, they don't have an installer for the Toyota motor?
installing harmonic balancer
Talked with the machine shop that's rebuilding the F.5. He asked about installing the balancer. On my searching here all I could find was everyone uses a big hammer to install. He will not beat it on. Where can I look for a balancer install tool?
forum.ih8mud.com
bobm
WTF, WTF, WTF!!!!
Call Yotashop and see if they have what you need. Or call Mosely motors, sure they would help, they do rebuilds all the time. 
- Thread starter
- #258
Got another nut/bolt. Talked with @cruisermatt for a bit and he gave me some insight and ideas. I'll let y'all know what works.
She'll go!
- Thread starter
- #260
The first threads on the crank snout are a bit rolled, no doubt from removing the nut the first time. It came off rough and always threaded back on tough. Gotta figure that out tomorrow.
Looks like m20x1.5 to me. Can someone check my work on that?
Looks like m20x1.5 to me. Can someone check my work on that?
Last edited:
