Was given two perfectly-sized bolts for this, 90mm long, "8.8" and what looks like a tie fighter stamped on the head. Need two more. Anyone have the thread spec handy? And do you figure 8.8 will do the trick? Maybe 16mm of thread goes into the block before it bottoms out. Thanks for any help!
Bolt Spec for Engine Stand? (1 Viewer)
- Thread starter jaymar
- Start date
This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.
Fj80oregon
GOLD Star
12mm x 1.25 x 30mm is the standard trans bolt so you add 30mm + whatever length your engine stand arms are. EDIT pitch is 1.25! My apologies.
Last edited:
- Thread starter
- #3
Thanks! 90mm perfect for these stand arms.
- Thread starter
- #4
Looking at McMaster-Carr site, no metric bolt I'm seeing has a grade rating, and the specs say hardness not rated. If I want to get an 8.8, it has to be SAE. This despite the fact that I have two metric 8.8 bolts in my hand, which I'm told came from McMaster-Carr. Site lists tensile strength on the metrics as 100,000 psi, which is quite a bit below Grade 8. These bolts are 18-8 steel. Does this make any difference, or am I splitting hairs here? Engine has all accessories in-place. Thanks for any help!
www.mcmaster.com
McMaster-Carr
McMaster-Carr is the complete source for your plant with over 595,000 products. 98% of products ordered ship from stock and deliver same or next day.
Last edited:
Fj80oregon
GOLD Star
I got mine local at a hardware store and they had 8.8 or 10.9 grade. Home Depot has them also
Fj80oregon
GOLD Star
You got a rebuild your doing?
mudgudgeon
Resident galah
You're splitting hairs.
Your Chinese engine stand will fold in half before you snap a 12mm bolt holding a static tensile load.
The bolts only need to be tight enough to hold the engine in place. You shouldn't need to be torquing them enough to stretch the bolt.
Strictly speaking the definition of grade 8.8 is not applicable to a metric fastener.
10.9 is roughly equivelant to 8.8
if you want to figure it out . . .
www.hiteshsteel.com
Your Chinese engine stand will fold in half before you snap a 12mm bolt holding a static tensile load.
The bolts only need to be tight enough to hold the engine in place. You shouldn't need to be torquing them enough to stretch the bolt.
Strictly speaking the definition of grade 8.8 is not applicable to a metric fastener.
10.9 is roughly equivelant to 8.8
if you want to figure it out . . .
Grade 8 vs 10.9 High Tensile bolts | Alloy Steel class 12.9 Studs
High Tensile is very strong, long-lasting carbon steel, find here the Difference between Grade 8 and 10.9 bolts and studs. Compare composition, mechanical properties, and strength.
mudgudgeon
Resident galah
I'm pretty sure I used old head bolts.
Thread was right, length was good for my engine stand.
Thread was right, length was good for my engine stand.
Not sure what you are looking at but McMaster does have graded metric fasteners. You can get 10.9, M12x1.75x90mmLooking at McMaster-Carr site, no metric bolt I'm seeing has a grade rating, and the specs say hardness not rated. If I want to get an 8.8, it has to be SAE. This despite the fact that I have two metric 8.8 bolts in my hand, which I'm told came from McMaster-Carr. Site lists tensile strength on the metrics as 100,000 psi, which is quite a bit below Grade 8. These bolts are 18-8 steel. Does this make any difference, or am I splitting hairs here? Engine has all accessories in-place. Thanks for any help!
McMaster-Carr
McMaster-Carr is the complete source for your plant with over 595,000 products. 98% of products ordered ship from stock and deliver same or next day.
I think people are confusing SAE and Metric ratings. Metric are 8.8, 10.9, 12.9, etc, SAE is 2, 5, 8, 9. An 8.8 is roughly equivalent to an SAE grade 5.
"ISO Class 10.9 fasteners are metric high-strength steel screws and threaded rods. They're commonly found in valves, pumps, motors, and other high-stress applications. They have a minimum tensile strength of 150,000 psi. Use them with Class 10 or higher nuts."
McMaster-Carr
McMaster-Carr is the complete source for your plant with over 595,000 products. 98% of products ordered ship from stock and deliver same or next day.
- Thread starter
- #11
Not sure what you are looking at but McMaster does have graded metric fasteners. You can get 10.9, M12x1.75x90mm
I think people are confusing SAE and Metric ratings. Metric are 8.8, 10.9, 12.9, etc, SAE is 2, 5, 8, 9. An 8.8 is roughly equivalent to an SAE grade 5.
"ISO Class 10.9 fasteners are metric high-strength steel screws and threaded rods. They're commonly found in valves, pumps, motors, and other high-stress applications. They have a minimum tensile strength of 150,000 psi. Use them with Class 10 or higher nuts."
McMaster-Carr
McMaster-Carr is the complete source for your plant with over 595,000 products. 98% of products ordered ship from stock and deliver same or next day.
I did NOT find those suckers, though I was looking for SS partially threaded. Hmmm...King bolt in Covina on grand ave, they work bankers hours like 8 to 4 now days
mudgudgeon
Resident galah
"Your Chinese engine stand will fold in half before you snap a 12mm bolt holding a static tensile load."
You know it's true, right??
- Thread starter
- #14
That's why it's funny. Though it does seem like an awful lot of weight to hang by a few bolt-tips, any way you cut it.You know it's true, right??
- Thread starter
- #15
Anyone care to guess again on that bolt spec?
Assuming McMaster-Carr sent what I ordered, that’s the wrong (or incomplete) spec. Bolt that fits is on the right.
mudgudgeon
Resident galah
Head bolts. 11mm x1.25mmpitch
mudgudgeon
Resident galah
Not at those prices, though I’m now $25 into the wrong bolts…
Can you return them?
Did you end up confirming thread specs with ARP?
I think I discovered steering box to frame bolts are the same thread, and similar length.
- Thread starter
- #19
Does anyone know, FOR CERTAIN, what this spec is?
MG: No idea on returns. Have ARP custom studs ready to test-fit at machine shop. (If I can ever get this engine on the stand...)
- Thread starter
- #20
I'm told these are the ticket:
www.mcmaster.com
McMaster-Carr
McMaster-Carr is the complete source for your plant with over 595,000 products. 98% of products ordered ship from stock and deliver same or next day.
Last edited:
