This piece of trim that's missing...
The upper 2 holes for mounting break off
The upper 2 holes for mounting break off
80 Series 3D Printed Parts (3 Viewers)
- Thread starter Outsane
- Start date
-
- Tags
- 3d printing fzj80
This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.
Why 3D print when you can buy original from Toyota for about $42usd?
This is so niche it's ridiculous, but I'd really like something to fix/replace the ashtrays on the rear doors of non-power window versions of the 80 series. It was really hard to find pics online, but here's some pics from a non-power window model GX variant out of Japan:
Placement is slightly different on the pov-pack version door trims, but the actual part seems identical. The problem with this part is the plastic outer "holder" for the ashtray insert, while looking similar, is actually made out of a different kind of plastic, and it goes very brittle over time. At this point if you just look at them funny they shatter, meaning the ashtray falls out and you're left with a void. Both of mine on my 80 are broken. I don't care about the ashtrays themselves, but the hole in the door doesn't look great.
I've got three ideas. One is just a blanking plate to cap off the hole, that screws into the tiny metal bracket that hooks on the door card, and closes off the hole. Essentially an ashtray delete. Or you could duplicate the outer bracket itself, so you can refit the ashtray. What I'd really love to do for my 80 is replace the ashtrays with usb ports for charging. Since I've added the door wiring harnesses (usually not present on base model 80s) so that I could retrofit central locking, I'd love to use the wiring for the power windows to each door to run USB charging circuits instead. I know @Delta VS has a few solutions in this area, but not for the base 80 rear ashtrays.
Placement is slightly different on the pov-pack version door trims, but the actual part seems identical. The problem with this part is the plastic outer "holder" for the ashtray insert, while looking similar, is actually made out of a different kind of plastic, and it goes very brittle over time. At this point if you just look at them funny they shatter, meaning the ashtray falls out and you're left with a void. Both of mine on my 80 are broken. I don't care about the ashtrays themselves, but the hole in the door doesn't look great.
I've got three ideas. One is just a blanking plate to cap off the hole, that screws into the tiny metal bracket that hooks on the door card, and closes off the hole. Essentially an ashtray delete. Or you could duplicate the outer bracket itself, so you can refit the ashtray. What I'd really love to do for my 80 is replace the ashtrays with usb ports for charging. Since I've added the door wiring harnesses (usually not present on base model 80s) so that I could retrofit central locking, I'd love to use the wiring for the power windows to each door to run USB charging circuits instead. I know @Delta VS has a few solutions in this area, but not for the base 80 rear ashtrays.
Oh, I should add, this part is definitely NLA.
How about a drivers side right arm rest, to fit down into the little box that's on the side of the center console? Are there any folks with 3D printers out there that could come up with something like this?
Have you though about remounting the plug like this so it all fits with no modifications?
You're welcome!
The single most overpriced POS plastic part on a 80. This isn't a 3d part request, it should be a metal aftermarket request with mounting options for add on accessories. If Dave from @Delta VS crawls back from underneath the rocks, him and his team should strongly consider a aftermarket replacement.
Pretty simple until then, when you remove this part release the bottom from inside and push the upper part up to release.
Hi Everyone,
I love this stuff and I have just purchased an Ender3v2 for making stuff for around the house and a few parts for my 1992 80 Series Landcruiser and I am having problems finding a part for the front A pillar grab handle .... I have looked everywhere to find a print file or something to help me print it and I cannot find it anywhere...
I have included a link below to a shop here in Australia that has the part but it is and has been out of stock for over 12 months... Does anyone have a file for this or know how to help me recreate this part.. I would be very appreciative of any help from anyone... Thanks In Advance Tim.
www.allfourx4.com.au
I love this stuff and I have just purchased an Ender3v2 for making stuff for around the house and a few parts for my 1992 80 Series Landcruiser and I am having problems finding a part for the front A pillar grab handle .... I have looked everywhere to find a print file or something to help me print it and I cannot find it anywhere...
I have included a link below to a shop here in Australia that has the part but it is and has been out of stock for over 12 months... Does anyone have a file for this or know how to help me recreate this part.. I would be very appreciative of any help from anyone... Thanks In Advance Tim.
Front Grab Handle Screw Cover Plug Grey suitable for 80 Series Landcruiser
Front Grab Handle Lower Screw Cover Plug Grey suitable for 80 Series Landcruiser 74616-60010-03
Outsane
Supporting Vendor
- Thread starter
- #33
Grab Handle plug Landcruiser FJ80 FZJ80
Grab Handle plug Landcruiser FJ80 FZJ80 I had a few missing Sold in a Pair, most of the cost is shipping and packaging.. The B-Pillar mount will come with a Left and Right side, Above the window handle par will cover one handle.
solvefunction.com
I sell em
I'm in Melbourne Australia.. do you have the print files or do you just sell the parts and if so how much for the cost of the part and postage to Melbourne Australia please.Grab Handle plug Landcruiser FJ80 FZJ80
Grab Handle plug Landcruiser FJ80 FZJ80 I had a few missing Sold in a Pair, most of the cost is shipping and packaging.. The B-Pillar mount will come with a Left and Right side, Above the window handle par will cover one handle.
I sell em
Headlight leveling window caps.
NorCalFJ100
SILVER Star
Keep me posted on this!!
Saw some tweeter pods that were made to fit the trim piece on the the inside of the door where the side mirror mounts.
Would like something similar but for a gauge, like a boost/egt gauge.
Would like something similar but for a gauge, like a boost/egt gauge.
Outsane
Supporting Vendor
The glow shift gauge is electronic and 52mm diameter. Not sure of the depth.
