cps432
SILVER Star
I’ll carefully pull them out this week. I have an other package to send off for another mudder. PM me and I’ll get it out this week if I can.
6X series Unobtainium (2 Viewers)
- Thread starter Cruiser Cult
- Start date
This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.
cps432
SILVER Star
Mine are in rough shape and I never wanted to install them. They’re too bent up to sit flush. However, they are 100% there including the gaskets that mate to the body.
There are 5 clips on each side. It looks like the back end has the pilot punched for the mounting screw, but it was never fully drilled out. The end caps are crimped on by the sheet metal.
There are 5 clips on each side. It looks like the back end has the pilot punched for the mounting screw, but it was never fully drilled out. The end caps are crimped on by the sheet metal.
Last edited:
cps432
SILVER Star
Last edited:
86aggie
SILVER Star
The clips were available 60 days ago from Toyota. Looked like they are used in a number of Toyota vehicles. The 'punch' or dent was not meant to be drilled out - rather a way to keep the rear plug in place.
I have searched for a GX badge for 7 years with no luck.
This came off a 24V HJ61 …
I do not know a part # yet … ?
I will carefully bring it back to like new condition ….. I hope
LED of course
I do not know a part # yet … ?
I will carefully bring it back to like new condition ….. I hope
LED of course
I have one used VX-badge from a HJ61 and it is different. It has grooves in letter V and X. The GX looks right.is this the correct VX badge ?
Jamieson22
SILVER Star
All the mounting hardware is still available I replaced the blinder clips, the little body receivers for them, the front mounting screws, and the body-side screw grommets as mine were barely hanging on.
For both sides:
9353064020 | 4 | $ 0.79 | SCREW, TAPPING |
9018904001 | 4 | $ 1.89 | GROMMET, SCREW |
6777220021 | 10 | $ 1.13 | CAP, FRONT DOOR TRIM RETAINER |
7586720020 | 10 | $ 2.59 | CLIP FOR ROCKER PANEL MOULDING SET; ROCKER PANEL MOULDING. |
Yes.is this correct ?
90999-00072
( is in active reproduction mode now as we speak , )
( is in active reproduction mode now as we speak , )
69057-90A11
HJ60 w/ GLOW feature step
HJ60 w/ GLOW feature step
Part # 07049-20511 PLATE , ENGINE NAME
2F Fire Brigade valve cover decal
Below is the original photos or it does not exist photos
and microfiche parts diagram as well …
I never knew about this, till this non-usa valve cover found me
and I heard the calling Inside me to reproduce it to help foster its historical significance in more then one way …
I also produced a TECH video on the topic as well …
It’s intriguing when you happen across BIG FOOT and it’s actually real and the 2F FIRE Brigade Land Cruiser was a REAL thing to in JAPAN !
2F Fire Brigade valve cover decal
Below is the original photos or it does not exist photos
and microfiche parts diagram as well …
I never knew about this, till this non-usa valve cover found me
and I heard the calling Inside me to reproduce it to help foster its historical significance in more then one way …
I also produced a TECH video on the topic as well …
It’s intriguing when you happen across BIG FOOT and it’s actually real and the 2F FIRE Brigade Land Cruiser was a REAL thing to in JAPAN !
Last edited:
4runner2FJ60
SILVER Star
View attachment 3245048@ToyotaMatt
it appears my boy Hunter is keeping it REAL too .........
- seeing this image and my period correct artwork passion for details that matter affixed in the correct PLANT A11 factory installed location
truly has made my Friday a warm one , thanks !
I just picked up a 60/40 front bench but the one I have doesn’t have the notched leg bolster like yours. Is that custom?
Also is there a special “center” console for the 60/40 front bench or it’s just the hand break and that’s it?
Only console I know of is covers for diff lock levers. There is not much room for anything else.
