- Thread starter
- #61
This is a HUGE help in making sure I’m not missing anything before putting the hoist on the motor and yanking. I really should have started by looking at the FSM.
1HD-FTE Conversion - Creating the Perfect 80 Series (4 Viewers)
- Thread starter MooseMichaels
- Start date
This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.
- Thread starter
- #62
1FZ is out! Thankful for good help.
Was unsure about the PS setup and what parts I would need to get for the FTE PS pump to run the 80 series steering gear, so I got to looking. Pulled the whole high pressure hose assembly from the 1FZ and it was a direct fit to the FTE PS pump, but you must bring the banjo bolt from the 1FZ over with the 1FZ hi-P line, due to the difference in thickness of the coupling.
FTE line, or what the salvage yard left of it:
1FZ line:
The rest of the PS system (original to the 1FZ chassis) should fit right up to my eye.
Was unsure about the PS setup and what parts I would need to get for the FTE PS pump to run the 80 series steering gear, so I got to looking. Pulled the whole high pressure hose assembly from the 1FZ and it was a direct fit to the FTE PS pump, but you must bring the banjo bolt from the 1FZ over with the 1FZ hi-P line, due to the difference in thickness of the coupling.
FTE line, or what the salvage yard left of it:
1FZ line:
The rest of the PS system (original to the 1FZ chassis) should fit right up to my eye.
Great job! All in now!!! I was wondering about the power steering lines, that's great to know.
- Thread starter
- #64
Separated both transfer cases from their respective transmissions so I can bolt the 80 series t-case to the A750F after cleaning it up. They are heavy. The trans did not come with the hardlines that route to the front to the trans cooler, partsouq doesn’t have them so am going to look for other sources. I’m trying to use OE parts as much as I can.
1HZ oil pan, oil pickup and gasket fit up to the FTE block really nicely, and the FTE oil level sensor was a direct fit. Man was that a whole lot of little bolts to torque up, and a whole lot of FIPG to razor blade off.
The low oil marker on the FTE dipstick is well above the top of the oil pickup, and the high marker on the dipstick is below the low point on the lobes of the crank, so it looks like the FTE dip stick and tube will be ok.
I was happy with how clean the rotating assembly looked. I cleaned up all of the gasket maker after installing the new pickup because I didn’t want to risk getting some small piece of RTV in the pickup channel. It seemed the factory absolutely hogged RTV on there, or that the pan had been off before.
The difference in profile of the 1HZ pan vs the FTE pan from the 100 series was dramatic. I suspect this means total oil volume is lower so I’ll be sticking to old school 5k mile oil changes once it’s sorted and running.
1HZ oil pan, oil pickup and gasket fit up to the FTE block really nicely, and the FTE oil level sensor was a direct fit. Man was that a whole lot of little bolts to torque up, and a whole lot of FIPG to razor blade off.
The low oil marker on the FTE dipstick is well above the top of the oil pickup, and the high marker on the dipstick is below the low point on the lobes of the crank, so it looks like the FTE dip stick and tube will be ok.
I was happy with how clean the rotating assembly looked. I cleaned up all of the gasket maker after installing the new pickup because I didn’t want to risk getting some small piece of RTV in the pickup channel. It seemed the factory absolutely hogged RTV on there, or that the pan had been off before.
The difference in profile of the 1HZ pan vs the FTE pan from the 100 series was dramatic. I suspect this means total oil volume is lower so I’ll be sticking to old school 5k mile oil changes once it’s sorted and running.
