linkage

Selling the linkage piece that connects to a FJ62 shifter. $80 plus shipping

Must take all items. I will not split or sell individual items. Some other smaller miscellaneous FJ40 items taken off a restoration will be included in the sale but not shown. $325 for all items

I will be converting a 3-speed to a 4-speed, keeping the vacuum actuated 3-speed transfer case and under dash shift mechanism for hi/lo. It is my understanding that because the 4-speed is approximately 4-6" longer, I will need to extend the hi/lo shift linkage rod. I measured the diameter as...

My '67 FJ40 was swapped with a 4 speed transmission under prior ownership, and the linkage was modified and interferes with the transfer case itself, preventing me from shifting into 4 Lo (Hi & Neutral are fine, but can't get it to click that one last notch into Low!) Looking for a replacement...

Hi guys, Getting a popping noise when I turn the steering wheel (can feel the clicking in the steering wheel) on turns with the steering linkage especially when going right. I have shop time and can use the vehicle lift next week, but the vehicle is not currently running. Would love to know if...

Here's one that will probably sell quickly. I know these are getting to be hard to find. It's a wiper motor and linkage from either a 78 or 79 FJ40. $SOLD plus the ride. Best to email me shmukter@pa.metrocast.net

I'm looking to return my 1977 back to the original mechanical linkage. When I got it it was set up with a holly. So I will need everything from the pedal to the carburetor including the bracket that bolts to the carb. The only component I still have is the bracket still attached to the firewall...

78’ FJ40 US-spec Been scouring the internet for photos of this but I can’t find a clear shot. I think this is a non OEM end (drag link end?) The threads are super long and I can’t remember if the castle nut should be snug to the bottom of the center arm or lined up with the hole. Kind of an...

Gday, Is anyone able to post some detailed or close up photos of their throttle linkage on a toyota 3b with an inline pump Cheers, Alex

My son came home from work today complaining that my cruiser would not go over 50 and the gas peddle felt sloppy and when I went out to look at it I found a screw had fallen out on one of the linkages. I'm hoping someone can tell me what size screw I need to get to replace it. I've attached a...

Hi all. My wipers have slowly been getting worse and hitting the bottom of the windscreen now. I got told about an "easy fix" of replacing some worn plastic windscreen washers. Ordered the (hopefully) correct parts, but I'm having a hell of a time getting them seated. Can anyone advise if in...

9/72-9/73 bellcrank carb throttle linkage assembly. $115.00 shipped.

If somebody has an extra floating around and can throw it in an envelope I’m willing to compensate :) pic to show the exact linkage courtesy of SOR. Zip code 99669. Thanks

I began the process of rebuilding my heater box, and it wasn't until I began putting it back together that I realized I was missing a part. Im missing the L-shaped Linkage that goes on the driver's side bottom front. Ive been advised that there may be different styles of this part. Seeing as...

Hi All, I began rebuilding my heaterbox, and didnt realize unitll i started putting it back together that im missing a part. Im hoping someone has a suggestion as to where I can source one. I circled the missing part in blue.

Came off a 1970 I parted. Not a complete setup. What you see is what you get $10 plus shipping

Does anyone make replacement ends for the shift linkage? Thanks

I'm missing a piece on my carb that the idle up actuator mounts to. This is for my 1985 FJ60. Please let me know what you've got. Thanks, Justin

I am looking for a picture of this part #21 in the attached schematic. This is for a '73 FJ40. Spector does not have a pic of it. Any help would be greatly appreciated. I believe that this only fit '72-73 but I could be mistaken. Here is the link to SOR - Land Cruiser Accelerator Linkage &...

Hello, I am looking for a linkage member for my 1967 FJ40. I have the original dash mounted, vacuum-assist 4wd, but the link I have, (shown below) I believe is for a 4-speed and is about 2-3” too long. I am hoping to avoid cutting this down and rewelding it to the correct size, so please let me...