birfield

I'm suspecting the grease leakage means these need attention. Just looking for a second opinion.

Can some one tell me how much room I will need to get long side axle/birfield combo out? That is how far from garage wall does hub need to be get the assembly out? 1968 FJ55 if that matters. Thanks.

Looking for a Birfield for a 77 FJ 40, with the wider hubs. This Birfield will be longer than most, measuring aprox 9.82 overall length.

Nice assortment of new parts that came with a large parts lot. $125 $105 shipped for everything. Please reply in thread. Thanks, Dennis -Toyota fuel filter 23030-24011 -Toyota 170 degree thermostat -Koyo 6306 bearing -Specter motor mount 040-08A -Specter birfield seals 080-59A -Toyota transfer...

Looking at purchasing the Birfield Seal/Knuckle Rebuild kit form Cruiser Corp. Is it a good kit and will it have everything i need? It says wheel bearings not included. Anyone know a part number for the wheel bearings? TIA!

Cautionary note: you can bend these things with a big hammer. [EDIT] - Figuring out if I need to tear it all out and start over, including the diff. Opinions vary as you will see below. Short version of learning is that you should most likely never need to hammer the axle home and that you...

I hosed my front axle birfield by hammering it home with a sledge to seat it in the new oil seal. My new oil seals are very aggressive and I had to hit it hard, slightly mushrooming the end of the birfield, making it worthless. All my fault, dumb mistake. Anyone have a used one sitting on a...

Hey guys, Need help troubleshooting the left front while in 4 wheel drive. When in 2 wheel drive and hubs not locked, it drives and turns with no problems. Hubs locked and in 4L, it goes forward and reverse no problem as long as the wheel is straight. Turn the wheel and get a clunking noise...

New, Made In USA birfield and axle set. Fits 91-97 80 Series OEM 24 Spline Had this set as spares, but no longer need them. Retail is $950 US new plus shipping, etc. Asking $700 US shipped or $1000 CAD shipped. More info here: Ultimate CV Axle Set for Land Cruiser 80 Series ('91-'97) - 24...

FOR SALE: $75.00 +S&H (OBO) Early Disc Birfield PN 43405-60013 $75.00 +S&H (OBO) Early Disc Long Axle Shaft PN 43412-60020 $75.00 +S&H (OBO) Pair of Early Disc Dealer Warn Hubs PM for details.

I wanted to post on here and see if I can get any pointers. I believe it is my birfield joints that pop in 4 low at full lock left or right. Took the square bolt out of the top of the knuckle on both sides and started greasing. They clear up but eventually always start popping again. They do...

Need some suggestions on getting the new Birfields to engage with the splines in the differential. I greased the axle splines with assembly grease and when I put the locker together I put grease on the those splines before I installed the differential on the axle. Today I finished the assembly...

I believe I'm gonna have to do a total front end rebuild. I've never done it before, but I've been researching, and collecting all the necessary tools to do the job. Should I clean and rebuild the entire assembly or get replacement parts (Birfs, inner axle rod, etc). I wanna do this right, so...

Real time help. I'm doing a knuckle job on a '92 LC axle. The DS was in rough shape with failed seals and gnerally a mess. (No history on this unit) The ball end of the axle housing is fine on the inside, but had some pitting and a few deep Mars or scratches. The pitting I think is ok. I've...

I'm doing a knuckle job on a '92 LC axle. The DS was in rough shape with failed seals and a missing bearing presumably due to a field service. (No history on this unit) The ball end of the axle housing is fine on the inside, but had some pitting and a few deep Mars or scratches. The pitting...

Off my 1997 FJZ80 with ABS tone rings. About 230K miles on them. I purchased truck with 190K about 6 years ago. Got new ones in preparation for a long road trip. They seemed to be fine - just overzealous on front axle rebuild I guess. You pay for shipping and they will be yours. Just...

Putting the Left side knuckle back together, and the Birfield has what seems like a lot of play in it compared to the passenger side. Anyone know the tolerances for play on these?

I broke a Toyota Mini Truck drivers side axle shaft. Do you have one, or a set to sell? Factory, Longfield, Tell me what you have! Thanks 713-419-9074

I am looking to install some longfield/rcv birfs in my 40 series but I have a problem that I have a BJ70 series front housing with a cable locker. I can get a Longfield super set and a longfield inner axle with a long spline. I can get a RCV ultimate set but don't know if there is any long...

Hello Everyone, I changed my front axle late last year and have some leftover parts from the old one for sale: Here's a set of marlin crawler high steer arms. I will press the new pins in for the next owner. Also have the knuckles if someone wants them. Also for sale are these Longfield...