Is there a full float conversion available anywhere that lets me keep my 10 Spline Diff?? All I have found is conversions with 30 spline???
Thank you,
Ben
Iconic cruiser ready for adoption. Own a piece of history. You may have seen Rocky the 40 flying around the web or Cruise Moab. This is @cruiseroutfit 's first cruiser he built as a teenager with his Dad in 1995. She spent some time around Utah and a farm in Idaho. I acquired her from Jim of...
Toyota landcruiser fj40 for auction! Located in finland
More information you can find from here
Huutokaupat.com - Suomen kiinnostavin huutokauppa - https://huutokaupat.com/4425357/toyota-land-cruiser-1968
=========== NOTE - These are not mine, contact the seller via the Craigslist Ad =================
https://fresno.craigslist.org/pts/d/sanger-toyota-fj40-landcruiser/7672892968.html
1968 Toyota fj40 Landcruiser clean title on non op $8,500 or trade 559246o37six
Hi guys, my gauge cluster has some issues specifically the temp and speedometer. The sender is fine for the temp and I’m troubleshooting the speedometer. My question is if there are any replacements for a 68 vintage truck?
With a new fuel sender, the fuel gauge only goes to about 3/4 to 7/8 full when I articulate the float full up. The gauge follows properly when moving the float arm part way. When I set it at full down, the gauge indicates past empty.
I measured the unit resistance with two DMM's, and the...
Installing a front windshield and aftermarket gasket from CCOT. I started off having my insurance Handel the replacement. After multiple companies said they couldn’t do it my insurance said they would reimburse me if I did it.
So I took my front windshield to a local glass company. The only...
I will try to list all the meaningful details below:
1968 FJ40 runs and drives, clear 1968 title. (located in zip code 53406)
1976 FJ40 drive train (factory disc brake front end and the 4-speed). Not sure if the rear axle assy is 68 or 76. I could take a look at the rear drive shaft flange to...
Hello All,
Trying to get an idea of how much my Scout might be worth because I might want to sell if it is worth it.
1968 Scout 800
Registered in CA until Jan 2021
Runs and drives (daily driver)
26K original miles
Original International V8
Electric cooling fans
4 spd transmission (not sure but...
Just replaced starter and now when starting it grinds as if not lining up properly. I've been told by non cruiser folks it needs shims, although it didn't have them on the old starter. I thought it'd be best to get feedback from y'all. Thanks!
New to me, April/May 1968 FJ40, according to the VIN FJ4057032
Trying to sort through a few things as I'm not at all familiar with very early 40s.
Are these the correct tail lights/brackets? Also, were there reflectors next to the lens, on the bumpers?
Web pix are all over the place.
Added value by Toyo_Judson posted Sep 4, 2015 at 10:01 PM
FJ55 key ring...Also included in sale is a separate 1F motor with Rochester carb and GM dizzy. I bought it used but it was running when pulled.
Along with 1968 FJ55 that has a 1.5F motor, new Trollhole Carb, New coil, rotors, and parts...
hey giys I just got a 1968 FJ40 1t motor with ~69,00 miles on it. Body is shot but frame appears to be in good condition. HAs some great parts (both axles, new brake cylinders and pads on one tire so I assume it is aon all four as the guy said he had brakes done, brand new radiator, seats are...
Added value by Toyo_Judson posted Sep 4, 2015 at 10:01 PM
Also included in sale is a 1F motor with Rochester carb and GM dizzy. I bought it used but it was running when pulled. Along with 1968 FJ55 with 1.5F motor, new Trollhole Carb, rotors, and parts for front disk brake swap (knuckles and...
This 68 FJ40 is located in Sacramento CA. The Cruiser runs and drives well and is mostly stock. It was upgraded to the 2f motor, but still has the 3spd column shift. It is not perfect by any means but is a great start to a nice project or drive it as is. Has a small amount of rust on the...
Does anyone sell replica wheels the white ones. Not the steelies with hub caps. I need a set of the white ones with very little back spacing and will clear the screw in the brake rotors. Thanks
I need some factory unions for front and back of 68 fj40 all drum breaks I think rear part number is 086-77A. Front 086-10A and still have most of rhe f motor factory complete but torn down also clutch and factory Clutch and pressure plate and bell housing