How’s it going Mudders!
Trying to save a buck and purchase a complete power steering pump from Toyota Parts Deal. Can someone chime in on what’s actually required. It appears that this is the part number/unit I require...
How’s it going Mudders!
Headed to SoCal third weekend of March towing my Mazda RX-7 to a shop but in doing so it looks like I’ll be doing a little bit of Mud-Shipping a bumper on the way down for @hdj8081 and some wheels coming up for @benroberds. I should have some space in the bed and some on...
Free 80 series wheels and tires! Tires are old but hold pressure. Probably just fine if you’re rolling around the shop. Has a spare wheel and tire too. Oddly the tires really aren’t that cracked?
Empty bed except tentatively a seat in the bed of the Tundra around the third week of December. Will tow a car hauler trailer at an additional expense.
On the road and the truck kind of felt a little different and ran slightly warmer. On average I don’t see above 190 degrees while I’m on the move on the scan gauge but then it was 193 to 198. After I pulled over to take a look I seen I had some coolant spatter from the overflow. Maybe it was...
Good morning, a bit of a tall order here. I’m looking for a heavier spring then my current setup. I currently have the Icon 3” kit but I used 30mm spacers to level out the rear since I yielded a bit more then 3” up front. I also have Airlift airbags out back specifically for towing.
I’ve...
Pretty sure it’s finally let go and the mis-alignment of my belts is because of it. Unless you think the crank bolt decided to walk itself out.
Have a look at the amount of rubber showing on the back side of the crank pulley.
It kept sleeping the alternator belts and I couldn’t figure out why...
After finally finding the culprit of noise that eluded two shops and changing a ball-joint I checked my nuts and seen one very loose. With the air ratchet I began tightening and this happens. Did I over-torque or was it already stripped when they rebuilt my diffs and it didn’t take much for it...
Just curious if anyone is making this trip and has a trailer for an RX-7.
I’ll probably get a quote from @Riverrunner as well.
Currently bidding on it now at BaT.
Just curious what you guys are using to protect the harness for those of you still running an EGR? Is there a bolt in plate or what wrap do you guys like?
I’m seeing some damage to the harness but it’s on the exterior only. Also, I believe there is plastic clip that should hold the harness...
Just to confirm, does this look right to you? I pulled both off at the same time to replace hoses believed I may have mixed them up.
Should these two be flipped?
I have one radiator out of my 97 and one radiator out of my 85. The one for the 60 should be rodded out but the one for the 80 is fine. No longer need as I just installed a Ron Davis as a pre-emotive measure.
$25 bucks each picked up. I will only ship one of these as I still have the box that...
Looking to pick up a set of chains or cables for 35” KM3’s. I was curious what you guys use under what conditions and why?
I have a snow wheeling trip next month but I’d also like something for highway use when required by law. Is it best to have two types for different purposes?
Hopefully...
Part of the filling system over-haul I’m trying to access one of the last things on my list. How do you remove the thermostat bypass coolant pipe. Apart from the the 2 12mm bolts, should it just pull out?
Also teaser photo…
Good evening MUD gurus,
As my rabbit hole of replacing all coolant hoses led me to replace all EGR components i’m left at the intake manifold.
Is there an easy way to do so. I did watch a video on YouTube and learned a good piece of advice on ensuring you pull it off carefully so you don’t...
As the title says, if like to know how engage and disengage the 4wd. The previous owner mentioned the vacuum may not be hooked up so further more I’d like to know the diagnosis portion as well to ensure it’s functioning.
Thank you in advance.
The truck is all original by the way.
It’s highly likely I didn’t search enough I’m sure but I have 2 hoses to go including the PHH…of which I can’t even locate. Must I remove the throttle body or intake?
Any advice would be appreciated!
Thank you in advance.
EDIT: so it may jot be the PHH I still need to change but the two in...
Started with me prepping to receive some parts and finishing wiring up the OEM lockers to the ARB’s, CDL Switch and 7 pin mod.
Well in the process I removed the plug on the portion of the harness where the CDL switch goes. I was unaware it acted as a jumper cable to allow the CDL to disengage...
Hello fellas, putting up our recently acquired 40. Picked this up from another Mud member back in December in Cedar ParkTexas.
Purchased this for the for the wife to put around with the boy in town. Took care of registration and plates. Well…the wife didn’t particularly care for the 3 on the...