Search results for query: *

Forum search Google search

  1. B

    Aux Fan wiring help

    I would like to install a pusher fan to increase AC cooling during summer together with a revamp AC system and parallel condenser. I'm not very good at wiring, even reading electrical wiring diagram so I would need the instructions that a 6 year old would understand. Reading ABC of cooling, I...
  2. B

    Identify rear heater hose

    Is there something supposed to be connected at the end of that tube? I did the PHH a while back but I cant remember. I’m not losing coolant or anything. Thank you
  3. B

    Normal boost psi with supercharger?

    I installed a boost gauge just to see how much boost my truck is making. I only see maybe 2-3 psi and 4.5 psi in higher rpms with heavier throttle. Does it seem normal?
  4. B

    Is this a defouler? Intake manifold vacuum line

    I removed both by o2 sensors for my lx450. The picture below is the rear o2 sensor. Is that a defouler? Voltage for both my sensors are 0.05-0.13. The second image is the intake manifold vacuum. For what I understood, that vacuum line is sealed off in supercharged 1fzfe? That will not cause a...
  5. B

    Misfire cel then p0125 cel

    I have just finished installing my trd supercharger. Rough idle, almost stalling. I checked all the vacuum lines that were involved during the install. CEL turned on with “multiple misfires” and misfire codes on all cylinders. After driving for a little, the rough idle went away but then p0125...
  6. B

    P0120 tps

    I just finished installing my supercharger. Fired right up but with CEL P0120 and idles around 1500 rpms. I did not disconnect the cables from the throttle body, i kept the whole assembly together. I used solder seal connectors when I spliced both ias/tps. I searched how to test the tps but I...
  7. B

    Throttle body / intake runner gasket for supercharger

    One on the left is similar to what I received from Jon Bond Performance. One on the right is the oem gasket from the throttle body to intake manifold. The first one does not have the extra hole. Which is the correct gasket for both supercharger to throttle body and intake runner to intake...
  8. B

    Venom 400 Module

    This module/computer came with the supercharger I purchased. Previous owner said it os to increase fuel in low throttle. Has anybody used this with their supercharger?
  9. B

    Add washer as radiator fan spacer? Separating FIPG help

    My radiator fan spacer (0.187” inch thick aluminum) is not enough to clear my supercharger tensioner pulley. Is it safe to use lock washers as additional spacers? I’m thinking of maybe 2 spacers per stud. Also maybe I can find a tensioner bolt with shorter head for added clearance? Here are the...
  10. B

    remove tension before removing crank bolt?

    will it be safe to remove the crank bolt without loosening the tension? I will be installing the supercharger crank pulley and was wondering if I can get away without doing so. Thank you
  11. B

    Radius Arm Install

    My delta arms came in about a week ago. Been busy for the Holidays and looking to install after new year’s. Currently have an icon 3” lift. I would like to get some advise. Thank you
  12. B

    Do I loosen and retorque control arms after lift?

    I’m current in the process of finishing up installing my 3” icon lift. No control arms or sway bars were exchanged. Do I loosen the upper and lower control arms and retighten when the vehicle is back on the ground? Thank you!
  13. B

    Wanted  CA: FZJ80 supercharger parts (fan blade or orange SC fan clutch. Heater pipe. Intake runner)

    Recently got an incomplete supercharger kit for my 80 series. Looking for some parts to complete. -Intake runner (found) -longer orange Fan Clutch for supercharged 1fz-fe -heater pipe -intake elbows (found) Thank you
  14. B

    Incomplete Supercharger help

    Purchased an incomplete Magnuson Supercharger kit. For those who have installed or experience with them, can you help me identify parts needed to complete it? Intake elbow, hoses and bolts seems easy to replace. 1.) intake runner is missing. Waiting for previous owner to reply if he has it...
  15. B

    Wanted  3” dual rate/progressive suspension for fzj80 (SOCAL)

    Looking for a 3” lift with dual rate / progressive springs. Located in SoCal. Thank you!
  16. B

    Anybody running rrw rr7-h?

    I saw a photo here of an 80 with rr6-h wheels 17x8.5 but mentioned some modifications. I PMd the user but has not gotten back to me. I really like those wheels and wondering if anybody know what the issues are? Thanks
  17. B

    Anybody running Method MR310 con wheels?

    I like a dish / concave look on 17”s. What are some other examples and correct offsets? Thank you
  18. B

    Koyorad owners need help

    Found my radiator is leaking from the top seams. This is after I treated my radiator thermocure and flushed with distilled water (removed old debris causing it to leak?). Anyways, looking for a new radiator. Was initially looking to get oem but cheapest I could find is $428 plus tax and ship...
  19. B

    Wanted  Socal: slinky icon intermediate suspension 3” lift

    Looking for a set of slinky-icon long travel. Thank you!
  20. B

    Wanted  SOCAL: SCS F5 17x8.5 80 fitment

    Looking for new wheels! With or without tires. Interested only with 35s. 80 series fitment pls!
Back
Top Bottom