I purchased the 36132-60021 output shaft bearing retainer from Toyota for my '88 FJ-62. Took the old one out, banged in the race into the new retainer then I noticed that the oil seal was way smaller than the opening.... shoot. Anyone know what seal I should use in the new retainer?
I had my carb recently rebuilt and when it came back I noticed a peculiar thing about it when I was adjusting the fuel mixture. normally I tried to find the middle of the sweet spot for this setting. After setting the timing I would turn the screw out until it started sputtering then I would...
I had rebuilt my transfer case last year but now after the H55 Swap I need to reset the rear output shaft bearing preload. This means removing the rear output shaft rear bearing retainer, problem is that I can't get this thing off. WTF. too much Anaerobic Sealer...?
Stupid thing to ask on...
I have a questionable perceivable click when pulling back and forward on my transfer output flange, which makes me question the preload on the bearing. I have the original shim but the bearing changed a couple of years ago. Sooo, I wanted to reset the preload. To do so I would love to find a...
So I just installed a brand new temp sender (83420-20011) in my F engine head (3/73), just because it was easy to do and eliminated any ambiguity from the readings.
Not sure what the old sender was and how it mapped per temp. Since I'm not sure I can trust my gauge, i went to the sender to...
From my research, I believe there was an update to the front seats during the update in either 9/72 or 9/73. They started having greater side support as it looks as if they got rid of the bench option.
However, I'm a little stumped. I have a 3/73 but it looks like I have the slimmer seats...
I'm trying to clean up bonded up holes for the rear view mirrors and was hoping to tap them, so I didn't want to screw it up ( pun intended)
Anyone know the diameter and thread width? The bolt number is 93239-15012, which states
Tensile strength of 1T
50mm diameter
12mm length.
I have to...
I have a case of Swiss cheese on my front panel. I'm trying to decide what is a stock hole and what was created by the many overzelous owners of this 1973 FJ40.
Here's what the 1973 FJ40 looks like in the LC Museum. The panel looks like it's completely different.
Rebuilding my J30 3 speed transmission. the springs seem to have gotten eaten up, not sure how they got out. I can't seem to find any OEM ones available. Anybody know if I can use the 4 speed springs or any other springs?
thanks,
Just bought my first FJ40, yay (I think).
- 1973 (FJ40145310) Not sure what config it originally came in. F155 with j30 tranny.
- No roof, no doors, no wipers
- All blacked out, everything... yikes.
- No front brakes, back left locks up easily
- throw out bearing noise? after a noise, it goes...
My buddy was looking at some JDM 81s at Seldon motors. He heard that one of them just got shipped to Austin and was wondering how they were to deal with. Any MUD guys pick that one up?
I bought the new front runner 80 SLIMLINE II roof rack. This rack has 4 legs on each side instead of 3 which is great, but there is a problem now as the back leg is really far back and it doesn't really allow the rack to be as far back on the roof as I'd like. Rack being far back helps me to...
I am trying to refresh some of the seals in the sunroof, hence I bought 4 slide roof seals. The old ones on the corner seem to be thicker and more spongy, but the ones that came are hard and I'm not really clear if I need to pull something back to reveal an adhesive? Anyone replace these yet...
Has anyone installed the Frontrunner Slimline II rack recently and did you need the leg spacers? How did it all work out, as I've heard stories of front and back legs still being too short. Funny enough, Frontrunner doesn't directly sell them but they did include two pair in the box. so I'm...