1MAC

October meet up-10/4/25 at Donut King 2320 Armour Rd KCMO from 7:30-10ish. Tell all your cruiser loving friends.

Thanks again to all the board/club, Kessler’s, out of state guests and everyone else who make this event happen. Weather was great and wheeling sensational! We had 35 driver registrations this year ! We are running more shirts and will get...

I went with a 17 x 9 0-offset from Raceline.

Roo and I went on a road trip and hooked up Mr. Riggs.. Also grabbed a couple axles and some other stuff for customers.

You need a copy of your EWD. 😁 You can directly power the reverse lights from the GSS-3000. Send power to pin 7 on IH1. It should be a R-B wire, but depends on year and model. This is from a 1997 EWD.

Looking for a 91-94 transfer case shifter base 36344-60021 shipped to 66224. Thanks

Another happy owner of F5s

Tires are here! 35x12.50-17 from our friends at Kansasland Tire & Service 🤙

Mostly to receive cheeseburgers, etc...

Pussy. :lol: :flipoff2:

Is the 2nd start button engaged?

My truck just got inspected and passed! I am thrilled. I am in Mass, and I wasn't quite sure it would. Weak-ass factory parking brake.....and it couldn't hold the motor at 1300 rpms as required for inspection. My guess is that they don't really...

Second PM sent. Awaiting reply. Thank you.

I’d love to do a comparison, since mine is essentially the procomp kit they used to offer before procomp discontinued 40 springs.

I've been struggling with this hose on my LS swapped 40 for a while now. Tried a swivel water neck but it leaks. I also bought a straight water neck like this one to see if I could make it work. Just found your post and thought - "Perfect! Now I...

I changed the thermostat housing as I struggled to find an off the shelf hose that would work with the original t-stat housing that points to the passenger side. Some of my issue is that the motor is probably an inch or two closer to the radiator...

I'll take it. PM sent.

Exactly. I actually just did this over the weekend in order to replace all of my gauge bulbs along with D light bulb (and the other 9 bulbs). It’s pretty easy after you remove the dash parts. It’s just 4 screws and 4 wiring plugs, then wiggle...

Hi guys fellow Torfab / Swaptime 80 series swapper here and I have found a pretty simple solution to the Torfab shift linkage situation. I found the Torfab tab that mounts to my 8l90 transmission fit perfectly but the angle was off by a few...

Clean up the OEM engine harness, using the guidance at LT1swap.com . I did it on my 40 and had no difficulties. You can send your computer to him and he will remove VATS and load a basic tune to get you going.

Here's mine - I like overkill! The big terminals are off ebay and are meant for the boom boom big stereo guys. Outgoing wires are to winch, Switchpros, Redarc BCDC, ARB twin compressor and Blue Sea Safety hub for power distribution to various...

For anyone considering putting in a Koyo, here is a current photo of my Koyo C1917 the PO installed 60k miles ago.

Rostra makes a DBW cruise control system that connects to the pedal, basically controlling speed through pedal actuation. The switching system to set speed, accel, deceleration etc is simply switched with momentary switches. That’s where a stock...

Any progress on the engine swap? Enquiring minds want to know!

You’ve got the right attitude and you’re blazing a trail for all us on the sidelines. Keep the great work up! I know I’m taking tons of notes and accumulating parts to do the same swap on my 80 with a hole in the block…