What Did You Do with Your 80 This Weekend? (96 Viewers)

[Greg McNally]

People didn’t flash you isn’t the litmus test to the lights not blinding them. Never out these LED bulbs in halogen housings. It’s still blinding people and is illegal is most states.

Standing in front of the truck they seem to have a good pattern and cutoff as they should. I have the in cab adjustment for the aiming set on the lower end down towards the road.

I would be surprised if the national chain I bought them from would be selling them if illegal in Canada. But your right; I should make sure and double triple check that I'm not blinding people.

 

[TheLCProject]

Bought it back after 5 years of relative neglect. Not sure what my goals/plans are.

We will start with a full interior removal and cleaning. Lots of oil underneath with a good chance it's just the valve cover gasket and oil pump housing. If the oil pan isn't leaking I'd be ecstatic but there's so much s*** underneath who knows.

I already fixed the front bumper misalignment on the passenger side by jumping on the corner of the bumper. I think we are going to get along fine though.

I don't know why I did this to myself.

Going to try not to get too upsidedown in it but it's already too late.

 

[brockdeck]

Bought it back after 5 years of relative neglect. Not sure what my goals/plans are.

View attachment 3391180
View attachment 3391181
View attachment 3391182
View attachment 3391183
View attachment 3391185

We will start with a full interior removal and cleaning. Lots of oil underneath with a good chance it's just the valve cover gasket and oil pump housing. If the oil pan isn't leaking I'd be ecstatic but there's so much s*** underneath who knows.

I already fixed the front bumper misalignment on the passenger side by jumping on the corner of the bumper. I think we are going to get along fine though.

I don't know why I did this to myself.

Going to try not to get too upsidedown in it but it's already too late.

Happy to see you back in an 80. Maybe some videos to come...?

 

[OffRoadScott]

Who will do your install?

Either Scott at Higgy's Cruiser or the same person that did the 3rds for my bosses race team.

 

[TheLCProject]

Happy to see you back in an 80. Maybe some videos to come...?

I hope so

 

[Marco Lau]

Overhaul the AC system this week, new compressor, dryer and expansion valve. Recharged the system yesterday and it is blowing COLD again, Running out of time, but the rig is ready for our annual Rubicon/Sierra Trek for

the next week and a half.

 

[highsierra4x4]

Exhaust is done Supra sounds

 

[seekay46]

Exhaust is done Supra sounds

How’s the drone with the dump pipe?

 

[BILT4ME]

Exhaust is done Supra sounds

Make sure you route that outside the body or it's gonna cook some stuff.....

 

[highsierra4x4]

How’s the drone with the dump pipe?

Haven’t been on the road yet still building some stuff but it really is pretty quiet. It’s only temp to get ready for my rubicon trip. Time and money lol

 

[Rouleur]

 

[Fj80oregon]

Decent start for a hour of tearing apart to remove this beast! Should be out Saturday and to the shop Monday for a full rebuild!

 

[Ecliff5]

Drove to Canada for the first time.

Flexed her out on a Little Rock and then flexed out the mini cruiser crawler.

 

[nigelsiam]

Drove to Canada for the first time.
View attachment 3392111
Flexed her out on a Little Rock and then flexed out the mini cruiser crawler.
View attachment 3392114
View attachment 3392115

How was the border crossing process?

 

[highsierra4x4]

Little work today

 

[Yossarian]

Putting the 80 to work. Losing approximately 5000' in elevation certainly helps.

 

[Ecliff5]

How was the border crossing process?

Smooth, no wait. Right through in and out.

 

[Dusten]

Left for a little road trip with the kids

 

[jcardona1]

Awesome 3D printed consoles made by @Ballsie

 

[Stiles]

Awesome 3D printed consoles made by @Ballsie

View attachment 3393307

View attachment 3393308

Awesome instruments