ARCHIVE WabFab Off-Road Aisin Manual- Hubs New, Used and Refurbished

[waskillywabbit]

Dials

Faces

Finished Toyota IFS pair

Broken bolts? Punch them out

One side clean and polished.

One clean and polished. One not.

Got to get a few more bolts but these are done

 

[waskillywabbit]

Rebuild parts here for IFS (use the diagram)
http://www.wabfab.org/component/opt...ge,shop.product_details/pop,0/product_id,906/

Rebuild parts here for SFA (use the diagram)
http://www.wabfab.org/component/opt...tpl/page,shop.product_details/product_id,907/

Refurbish parts here
http://www.wabfab.org/Aisin-Manual-Hubs/Aisin-hub-dial-o-ring/flypage.tpl.html

 

[Medic83]

Will sell just the faces without the body.

 

[waskillywabbit]

Dials/Faces sent for Refurbish
How I got them

Cleaned, degreased, blasted and prepped for powder

How they went back

Complete Refurbish
Disassembled for cleaning

Dials/Faces cleaned, degreased, blasted and prepped for powder

Cleaned, degreased and ready for regreasing and reassembly

Refurbished

 

[waskillywabbit]

Disassembled and ready for cleaning

Dials/faces blasted and ready for powder

Front corner pair finished

 

[waskillywabbit]

Middle pair in the picture above

Before cleaning and polishing

After cleaning and polishing

Done

 

[1973Guppie]

check this WHOLE thread and see the reviews on Wabfab, buyer beware.......

 

[waskillywabbit]

This weekend's work.

A set of ASCO (AiSin COmpany) SFA Toyota Manual hubs that came in this weekend from Georgia.

A set of Aisin SFA Toyota Manual Hubs that came in this week from Alabama. One hub looked like the wheel bearing got hot an galled the hub body and ring. Check out the pics.
Notice the hub body galling and increased ID of the hub body.

Figured the hub ring was trashed but I got the hub body out anyway and this was what I found

This is what a new hub ring looks like on the inside

The old hub body cut out/up compared to a good hub body.

Since the old hub ring is trashed the customer opted to go with a complete new Aisin hub.

Another set of Aisin SFA Toyota Manual Hubs that the customer requested to change to IFS dials.
Cleaned up and ready for grease and reassembly while the dials/plates get powder.

Blasted and ready for powder and the rest greased and reassembled.

 

[waskillywabbit]

Aisin Toyota SFA Manual Hubs with IFS hub dials refurbished

ASCO Toyota SFA Manual Hubs disassembled and out of the parts washer (see before pic in post above)

Dial and face plate after parts washer

After blasting

After powdercoating

Completely refurbished

 

[waskillywabbit]

Toyota IFS Aisin Manual Hubs being refurbished

After a soak in the parts washer and degreasing

Dials and face plates had attempts to paint them on numerous occasions it appears

One blasted and one still bootyfabulous

Both blasted and ready for powder

 

[waskillywabbit]

One blasted and one still bootyfabulous

Both blasted and ready for powder

Finished.

 

[waskillywabbit]

Hub bodies straight from the junk yard with internals removed ready for cleaning, polishing and reassembly.

Dials and faces with numerous layers of paint, gunk and dirt ready to be cleaned, blasted, degreased and powder coated.

Dials and faces with the bulk of the paint removed. You can see the various layers that were on these hubs.

Dials and faces cleaned, blasted and degreased ready for some fresh powder coating and reassembly.

Yes, these are the same Aisin manual hubs shown in all 5 pics. These hubs are completely refurbished. It is a huge transformation from start to finish.

 

[waskillywabbit]

Got a set of these in last week to refurbish. Can you tell what they are? Solid axle minitruck stuff is on the right.

 

[phishtaco]

Long body Asco from a 76-78 FJ55. Do I win a free refurbish of mine? Ha

 

[waskillywabbit]

How they came to WabFab.

How they left WabFab to go their owner.

 

[waskillywabbit]

FJ 55 long body Aisin Manual Hubs

How I got them.

After disassembly and the parts washer

Cleaned up a bit and ready for blasting, polishing and powdercoating

Here's a progression to the finished product

The finished refurbished product

 

[01tacotrd]

They look great. Should be in my hands tomorrow. Thanks again

 

[waskillywabbit]

Out of the parts washer.

One blasted and cleaned ready for powder.

Refurbished

 

[Spook50]

Damn those look good.

That's always a good part of when I do a knuckle rebuild is how nice everything looks when it's all clean and put back together. I'll have to get my hub cover plates and knobs powdercoated the original FJ60 hub colors when I do it this time.

 

[waskillywabbit]

Everything Aisin Manual Hubs!