Steve ..... just out of curiosity why not convert over to rear disc .
Now what broke? repairs, mods, need help etc.
- Thread starter CruiseOrlando
- Start date
This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.
I like drum brake emergency brakes on the trail, Eldorado calipers with the emergency brake are getting harder to find, no longer need to be concerned about the axle walking out if it snaps.
A bigger reason is I'm cheap and already put too much time & money in a Cruiser axle.
Next axle on next trail vehicle will have disc brakes, full float and centered diff.
A bigger reason is I'm cheap and already put too much time & money in a Cruiser axle.
Next axle on next trail vehicle will have disc brakes, full float and centered diff.
I forgot the 60 has e-brake in rear brakes . I sure wished the 40 did , I can't for the life of me get mine to work like it should . I have replaced the whole system and still want hold .
You know if you have your axles done by April , you can bring it to Mardi Krawl .
You know if you have your axles done by April , you can bring it to Mardi Krawl .
Roky
I install a line lock brake in front axle on my 40 for tree reason one if rear axle drive shaft or pinion brake you still lock front brake second I used on a couple situation on the rock to shift the truck to the side locking the front and use rear tires work best when you using the winch to pull.
I install a line lock brake in front axle on my 40 for tree reason one if rear axle drive shaft or pinion brake you still lock front brake second I used on a couple situation on the rock to shift the truck to the side locking the front and use rear tires work best when you using the winch to pull.
I installed one last year and it works great . But I would still like the e brake to work along with the line lock . I guess once it warms up I'll have to get under it and see way its not working .
hi guys am new on this am working on a fj40 am doing an up grade on steering and i just had a set back with the spring hangers and the steering box i need help with any info of were to get spring hangers and were to get an 4 bolt 30 spline steering box
CruiseOrlando
Conveniently Enhanced
- Thread starter
- #347
Okay, I'm going to proxy for someone... let's see who can guess who first!
After the who is out of the way, I'll tell you the what
After the who is out of the way, I'll tell you the what
- Joined
- Jul 22, 2012
- Threads
- 584
- Messages
- 16,426
- Location
- Winter Park, Florida
- Website
- www.cruisermatts.com
Luis's 40. The diff cage gives it away. Looks like the carrier cracked? I've always assumed either the cross-pin or the pinion would shear first, rotational force against a smaller area ya know?
Time for a rear ARB.
Time for a rear ARB.
Last edited:
CruiseOrlando
Conveniently Enhanced
- Thread starter
- #349
There you go. I knew it wouldn't be hard 
He's been moving a lot of trees off his new properly. Apparently that was a little too much for the lockrite....
He's been moving a lot of trees off his new properly. Apparently that was a little too much for the lockrite....
Looks like the cross pin sheared and carrier broke before taking the Lockrite out.
The Lockrites have stronger steel than the diff carrier does.
It will be interesting to see the Lockrite after he pulls it.
That reminds me, I need to get a Lockrite or Aussie because mine is broke too.
The Lockrites have stronger steel than the diff carrier does.
It will be interesting to see the Lockrite after he pulls it.
That reminds me, I need to get a Lockrite or Aussie because mine is broke too.
CruiseOrlando
Conveniently Enhanced
- Thread starter
- #351
Steve, you're right on the money
He's getting an ARB for the rear. I think it's a regear time too. Tech-session time... if I wasn't so wrapped up with life and work I would have been at his house this weekend ;(
He's getting an ARB for the rear. I think it's a regear time too. Tech-session time... if I wasn't so wrapped up with life and work I would have been at his house this weekend ;(
Bret, Very good point. The contact area where the Lockright holes touch the center pin is small and concentrated.
I have an extra carrier too. I'm a little bit closer
I have an extra carrier too. I'm a little bit closer
hey am trying to get an ammo can to make a center console i have one but is like 10" wide can you send me the dimensions of yours
Sold the 60 years ago man, its now in TX somewhere, sorry..
- Joined
- Jul 22, 2012
- Threads
- 584
- Messages
- 16,426
- Location
- Winter Park, Florida
- Website
- www.cruisermatts.com
This thread kind of died, time for a revival. Chopped my rearmost crossmember off and sold my hitch receiver, welded in a 2x4" (0.25" wall) and 0.75" recovery points. And some tubes (1.5" 0.25" wall DOM).
Next is to box the rear frame start accumulating parts for Spring-over
Next is to box the rear frame start accumulating parts for Spring-over
Feel like I've already seen these pictures but it looks great.
Matt, Getting ready for 63" Chevy springs??
What's in store for the front??
What's in store for the front??
- Joined
- Jul 22, 2012
- Threads
- 584
- Messages
- 16,426
- Location
- Winter Park, Florida
- Website
- www.cruisermatts.com
Yeah I wanted to have a solid foundation for on boxing that rear section so my frenched shackles have a solid foundation, I'm kind of working a few steps ahead.
I'm putting a set of good stock FJ62 REAR springs in the front. With a shackle reversal (frenched).
- Joined
- Jul 22, 2012
- Threads
- 584
- Messages
- 16,426
- Location
- Winter Park, Florida
- Website
- www.cruisermatts.com
Do you have any Chevy springs sitting around?
