UNBREAKABLE said:
Amazing how far a stick of tube goes. Not very far at all.
Again, looking great.
Get off the computer and get to work.
JR
Builds My Current Build-up (billy bad-ass)
- Thread starter UNBREAKABLE
- Start date
This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.
Amazing how far a stick of tube goes. Not very far at all.
Again, looking great.
Get off the computer and get to work.
JR
- Thread starter
- #142
Thanks for watching guys...I'm gonna finish this damn thing if it kills me.
- Thread starter
- #143
H1's are back in! I'll post pics prob. tomorrow. I'M STILL WAITING ON MY LOWER LINKS! This is getting to be stupid, he has had them for a month! STILL NOT DONE! It's only 2 links...4 threads!
- Thread starter
- #144
Well, I got my links back today. I am so pissed, you have no idea. The guy F'd up 2 sticks $100 ea(roughly) So now he is gonna have to buy me 4 threaded inserts
1 link he threaded left handed 2x(and I can't even get the end to go in more than an inch!)
the other link he threaded right on 1 side and gutted the other! He tapped it 2x and cut all the threads out of it.
Here are the pics. It is kinda hard to make out though
I got them back before he could destroy all of them. Damn I'm mad
1 link he threaded left handed 2x(and I can't even get the end to go in more than an inch!)
the other link he threaded right on 1 side and gutted the other! He tapped it 2x and cut all the threads out of it.
Here are the pics. It is kinda hard to make out though
I got them back before he could destroy all of them. Damn I'm mad
That sucks man. I'm curious though. Why didn't you go w/ threaded inserts to begin with? They're not all that expensive, and I can't imagine the cost of machining was cheaper. Just curious.
- Thread starter
- #146
I had a REALLY good hookup on machining...The tube was thick enough that I didn't need the adapters....UNTIL NOW
Cutting and boring those tubes and cutting the threads is a 
job. Whoever hooked you up with the so-called "machinist" ought to share your pain.
job. Whoever hooked you up with the so-called "machinist" ought to share your pain.
I can only imagine that he tried to single point the threads and did not match them correctly. It is hard to screw up a tap that bad..
I don't think you got a really good hookup on machining
I don't think you got a really good hookup on machining
- Thread starter
- #149
He had a tap for the right side and was single pointing the left side...He can do it, I've seen alot of the stuff he's done. I don't blame the person who told me about him at all. He was just relaying a message, that's all.
- Thread starter
- #150
My tube adapters are in the mail from Polyperformance 6=$84 BUT I'M NOT PAYING FOR THEM!
NEWS FLASH: I am not able to afford coil-over shocks right now. I am gonna put airshoxs in the rear as planned but I am going to be putting coils up front. I found some kick ass coil mounting brackets from www.ballisticfabricaton.com and I'm gonna order them in a few weeks(unless I come into contact with some big $$$) $1200 for some blinging ass shocks is not worth not being able to wheel. I am going to get my engine and build my t-cases next and that is gonna be a chunk of change
List Prices
(1) Clocked Dual Case Adapter from Marlin Crawler $499
(1) 23 Spline 4.7:1 Gear Set $399
(1) 23 Spline Input Gear $125
(1) 4340 Chromoly Output Shaft from Bobby Long $240
(1) Clocked Twin Stick $200
(1) T-Case Rebuild Kit $184
(1) Rear Driveline Disconnect (FROR) $500(possibly)
ENGINE= 3.4L Tacoma V-6
(1) 3.4L 30K miles All accessories $900~
(1) R150 Bellhousing to mate 3.4 to R151F $?
NEWS FLASH: I am not able to afford coil-over shocks right now. I am gonna put airshoxs in the rear as planned but I am going to be putting coils up front. I found some kick ass coil mounting brackets from www.ballisticfabricaton.com and I'm gonna order them in a few weeks(unless I come into contact with some big $$$) $1200 for some blinging ass shocks is not worth not being able to wheel. I am going to get my engine and build my t-cases next and that is gonna be a chunk of change
List Prices
(1) Clocked Dual Case Adapter from Marlin Crawler $499
(1) 23 Spline 4.7:1 Gear Set $399
(1) 23 Spline Input Gear $125
(1) 4340 Chromoly Output Shaft from Bobby Long $240
(1) Clocked Twin Stick $200
(1) T-Case Rebuild Kit $184
(1) Rear Driveline Disconnect (FROR) $500(possibly)
ENGINE= 3.4L Tacoma V-6
(1) 3.4L 30K miles All accessories $900~
(1) R150 Bellhousing to mate 3.4 to R151F $?
Tapage
Club 4X4 Panamá
~ 3047!
- Thread starter
- #152
Here are my sliders to this point, they also protect the x-cab and tie into the bed cage and they will continue forward to protect the front fenders and tie into the front bumper
Side and slant view
Side and slant view
- Thread starter
- #153
I just wanted everyone to know that progress IS being made. I will post pics tomorrow night.
My tube adapters are here(not installed, just here)
I built 78.3% of my pass. side slider today also.
My tube adapters are here(not installed, just here)
I built 78.3% of my pass. side slider today also.
- Thread starter
- #154
here are the pics as of right now. I still need to do some gusseting and plating, but soon they will be done.
I forgot to take pics of the tube adapters, I'll get some shots of them tomorrow.
Also, I picked up 2 more sticks of tubing today AND I hope to go pick up a 3.4L this week sometime.
POST UP COMMENTS PLEASE! I feel as if no one is watching this build.
I forgot to take pics of the tube adapters, I'll get some shots of them tomorrow.
Also, I picked up 2 more sticks of tubing today AND I hope to go pick up a 3.4L this week sometime.
POST UP COMMENTS PLEASE! I feel as if no one is watching this build.
Looks good
I love the tube work. Looks great.
Oh, BTW, you are too damn smart if'n you did all them there computer drawings of yer sliders.
Don't worry about people not posting. Everybody looks, they just don't comment. It gets frustrating when you've done a bunch of stuff and only get one or two comments.
Keep at it.
JR
I love the tube work. Looks great.
Oh, BTW, you are too damn smart if'n you did all them there computer drawings of yer sliders.
Don't worry about people not posting. Everybody looks, they just don't comment. It gets frustrating when you've done a bunch of stuff and only get one or two comments.
Keep at it.
JR
- Thread starter
- #156
Aight, I like hearing reply's GOOD OR BAD AS LONG AS THEY SAY SOMETHING!
Not Bad
Not bad man. Looks like its coming along nicely. I gotta make it out there for the unveiling, or at least see it before you tear it down again for another rebuild.
Not bad man. Looks like its coming along nicely. I gotta make it out there for the unveiling, or at least see it before you tear it down again for another rebuild.
- Thread starter
- #158
DAVIS? is that you?
Fine, Fine... I check your thread just about every other day and I never say s***. Mostly because I don't know s***.
But it looks like you are having a good time either anyway.
I am curious to see how it ends up. Especially the front end. I'll be looking close at how that works for you.
Keep at it. We are watching...
Andy
But it looks like you are having a good time either anyway.
I am curious to see how it ends up. Especially the front end. I'll be looking close at how that works for you.
Keep at it. We are watching...
Andy
It's Me
Yeah, it's me. I figured i would sign up on here so i can comment on your project.
Lets see some new pics.
How's it coming along?
Yeah, it's me. I figured i would sign up on here so i can comment on your project.
Lets see some new pics.
How's it coming along?
