Forgot to post this here 
Dissent offroad modular front bumper (4 Viewers)
- Thread starter benc
- Start date
This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.
Really appreciate the pics. RTT looks rad. Bumper def takes it up a notch on the awesome scale.Here's a few more pictures just before we headed out for the weekend...
Adventure Teq
SILVER Star
Here is how my DIY kit turned out.
Had my brother weld it all up...
Dang dude. Killer photos of this righteous kit!!
What paint did you use for the bumper. I'm slowly working on my DIY kit and will be ready for paint soon.
Here's a few more pictures just before we headed out for the weekend...
Just sent you a PM...
Just sent you a PM...
can't wait to get my bumper....
Benc, will you do roof racks?
If so, may I suggest a feature that I need - detachable roof rack. my 100 is my DD, and driving around town with the roof rack sure wastes MPG; and don't want all those attentions. I think others might have the same requirement. I need it to come off easily after trips, where I can just joist up under garage studs. I have looked at Rhino, Baja, and Gobi. It seems Baja is the easiest to remove. 6 joints, each joint with 2 bolts. leaving only a small metal handle plate imprint to have minimal wind resistance. Nevertheless, its a pain to remove them, bolts on, off.
If there is a product that address this need, I will purchase it. I think time spent in R&D this removable mechanism will be more marketable than say, rear bumper. I see many removable rear tire carriers and cans. But not on the roof rack.. Once done, you can even file a functional patent.
Benc, will you do roof racks?
If so, may I suggest a feature that I need - detachable roof rack. my 100 is my DD, and driving around town with the roof rack sure wastes MPG; and don't want all those attentions. I think others might have the same requirement. I need it to come off easily after trips, where I can just joist up under garage studs. I have looked at Rhino, Baja, and Gobi. It seems Baja is the easiest to remove. 6 joints, each joint with 2 bolts. leaving only a small metal handle plate imprint to have minimal wind resistance. Nevertheless, its a pain to remove them, bolts on, off.
If there is a product that address this need, I will purchase it. I think time spent in R&D this removable mechanism will be more marketable than say, rear bumper. I see many removable rear tire carriers and cans. But not on the roof rack.. Once done, you can even file a functional patent.
I joined the club this weekend. Did not have Ben weld the tube section so had a buddy do it for me. Bumper looks good - going to check out some local powder coaters this week.
Sections & Tube
Center Section Mounted
Aligning Tubes
Almost Finished
Sections & Tube
Center Section Mounted
Aligning Tubes
Almost Finished
Do you have any better pictures of the land cruiser with full front tubing?
bluecruiser
SILVER Star
Bump. Do not wait until 2 months before next year's 100s in the Hills to decide you need one!! 
Bump. Do not wait until 2 months before next year's 100s in the Hills to decide you need one!!
My kit has been purchased working on delivery
duggy
SILVER Star
My DIY kit has been ordered too! What options did you go with, @LandCruiserPhil ?
Mine is in the powder coating phase. That phase was delayed by the which &$*@ing powder matches the OE bumper? phase.
I'll post pics when it's installed. And, if the powder is as good a match as I'm hoping, I'll post up the powder color name/code too.
I'll post pics when it's installed. And, if the powder is as good a match as I'm hoping, I'll post up the powder color name/code too.
Basic no hoops and no lights
