80 Series Factory Bumper Swing Out DIY Kits (1 Viewer)

This site may earn a commission from merchant affiliate
links, including eBay, Amazon, Skimlinks, and others.

Awesome!

Can it be secured on the passenger side?

And the DIY Tire Swing Out Kit (which requires welding at $875), that’s for the entire set up, yeah?


Thanks!
 
DirtyPepper said:
Awesome!

Can it be secured on the passenger side?

And the DIY Tire Swing Out Kit (which requires welding at $875), that’s for the entire set up, yeah?


Thanks!
Click to expand...

Yes! Available for both driver side and passenger side fitments.

The kit includes all the parts and guides, but obviously will require some tools and equipment.
 
SUMMIT CRUISERS Jr said:
Yes! Available for both driver side and passenger side fitments.

The kit includes all the parts and guides, but obviously will require some tools and equipment.
Click to expand...
Awesome!

Looking forward to it!

I’ll place my pre-order in a couple of days!

Shipping will be to Vancouver, WA.
 
We’ve hit a little over half way on orders as of this evening! Thank you to everyone so far!
 
jjdeneen918 said:
I’m probably pulling the trigger on this today.

What are the install tools? Specifically for cutting the bumper cap. A hole saw I assume? Is there a template of where to cut?
Click to expand...

I used my drill and a hole saw to cut a smaller hole for the spindle. Then I recommend bolting up the bumper wing and using the supplied template to trace out the full size hole, and then cutting that out with either a jigsaw or a larger hole saw. If you clamp things down and set in a piece of wood etc to give the hole saw center point to guide the bit, it's not too bad but the jigsaw or a dremel etc are probably a little easier
 
Just a few left! If you're interested, please reach out to lock down a swing out before this batch closes.
 
Kit production has begun! Thank you to everyone who placed a deposit with me for this batch
 
For everyone who is in on this batch, I just wanted to give a brief update! Machined parts came in last week and with some good work this weekend things are getting close. I was thinking I was going to ship out DIY kits first, but I’ll be shipping everything at the same time as that simplifies the processes when I’m packaging (and gives me a little more time to finish the guides). I’ll be welding things up over a few of the evening's this week/next weekend and then onto packaging!
 
SUMMIT CRUISERS Jr said:
For everyone who is in on this batch, I just wanted to give a brief update! Machined parts came in last week and with some good work this weekend things are getting close. I was thinking I was going to ship out DIY kits first, but I’ll be shipping everything at the same time as that simplifies the processes when I’m packaging (and gives me a little more time to finish the guides). I’ll be welding things up over a few of the evening's this week/next weekend and then onto packaging!
Click to expand...
SUMMIT CRUISERS Jr said:
For everyone who is in on this batch, I just wanted to give a brief update! Machined parts came in last week and with some good work this weekend things are getting close. I was thinking I was going to ship out DIY kits first, but I’ll be shipping everything at the same time as that simplifies the processes when I’m packaging (and gives me a little more time to finish the guides). I’ll be welding things up over a few of the evening's this week/next weekend and then onto packaging!
Click to expand...
Hi how much would everything be including shipping??
 
SUMMIT CRUISERS Jr said:
For everyone who is in on this batch, I just wanted to give a brief update! Machined parts came in last week and with some good work this weekend things are getting close. I was thinking I was going to ship out DIY kits first, but I’ll be shipping everything at the same time as that simplifies the processes when I’m packaging (and gives me a little more time to finish the guides). I’ll be welding things up over a few of the evening's this week/next weekend and then onto packaging!
Click to expand...
Hi how much total with shipping??
 
Production update! Overall things are going great, but the welding is moving a little slower than I anticipated. I’ve got all the frame brackets and wheel mounts welded and a few of the arms. I’ve been running into duty cycle issues on the old Miller 175 which has been frustrating when I only have so many hours to weld after work in the evenings. Anyways, once I get this round done, a new welder is going to be next on the list of needed tools!

IMG_9342.jpeg

I hate being behind what I originally told everyone for when I was hoping to ship these so if anyone has any questions or concerns, please feel free to PM me.
 
ZCaptn said:
I ordered a DIY kit. It is possible to get sent the instructions so I can pre plan what I have to do and wrap my head around the project please?
Click to expand...

Absolutely, I’ll PM you
 
Packaging kits this weekend! Be on the look out for final invoices being sent and kits will go out Monday assuming payment!
 
You must log in or register to reply here.

Similar threads

T4rod
80 Series DIY front bumpers and other products
Replies
0
Views
866
T4rod
T4rod
raisinhell2
80 series 1 FZ-FE catch can system ..
Replies
0
Views
487
raisinhell2
raisinhell2
springerVXR
3D SCANS . 3D MODELS . DRAWINGS . Land Cruiser 80
Replies
10
Views
1K
springerVXR
springerVXR
RuggedOverland
80 Series Repair Manual - Limited Time Discount from Rugged Overland
Replies
1
Views
1K
RuggedOverland
RuggedOverland

Users who are viewing this thread

Total: 2 (members: 0, guests: 2)

Share this page

Back
Top Bottom